MPC5125YVN400 Freescale Semiconductor, MPC5125YVN400 Datasheet - Page 53

• Manufacturer Part Number: MPC5125YVN400
• Description: IC MCU 32BIT E300 324TEPBGA
• Manufacturer: Freescale Semiconductor
• Series: MPC51xxr

Specifications of MPC5125YVN400

• Core Processor: e300
• Core Size: 32-Bit
• Speed: 400MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, USB OTG
• Peripherals: DMA, WDT
• Number Of I /o: 64
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.33 V ~ 1.47 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 324-PBGA
• Processor Series: MPC51xx
• Core: e300
• Data Bus Width: 32 bit
• Development Tools By Supplier: TWR-MPC5125-KIT, TWR-SER, TWR-ELEV, TOWER
• Maximum Clock Frequency: 400 MHz
• Operating Supply Voltage: 1.4 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Data Ram Size: 32 KB
• I/o Voltage: 3.3 V
• Interface Type: CAN, I2C
• Minimum Operating Temperature: - 40 C
• Program Memory Size: 32 bit
• Cpu Speed: 400MHz
• Embedded Interface Type: CAN, I2C, SPI, UART, USB
• Digital Ic Case Style: TEPBGA
• No. Of Pins: 324
• Rohs Compliant: Yes
• Cpu Family: MPC5xx
• Device Core Size: 32b
• Frequency (max): 400MHz
• Total Internal Ram Size: 32KB
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 324
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Chapter 3
Signal Descriptions
3.1
This chapter describes the MPC5125 external signals. It is organized into the following sections:
3.1.1
The MPC5125 signals are grouped as follows:
Refer to the MPC5125 Microcontroller Data Sheet at www.freescale.com for a pinout diagram showing
pin numbers and a listing of all the electrical and mechanical specifications.
Functionality, which is not a primary function, is not shown in
multiplexed. Multiplexing is shown in
Individual chapters of this document provide details for each signal, describing each signal’s behavior
when asserted and negated and when the signal is an input or an output. Power signals are described in the
MPC5125 Microcontroller Data Sheet.
Freescale Semiconductor
•
•
•
•
•
•
•
•
•
•
Overview of signals and cross references for signals that serve multiple functions, including two
lists: one ordered by functional block and one by alphabetical
List of reset configuration signals
List of output signal states during reset
DDR memory interface signals
PSC interface signals
I
LPC interface signals
NFC interface signals
EMB interface signals
DIU interface signals
2
C interface signals
Introduction
Signals Overview
A bar over a signal name indicates that the signal is active low, such as
HRESET (Hard Reset). Active-low signals are referred to as asserted
(active) when they are low and negated when they are high. Signals that are
not active low, such as MODT (DDR2 on-die-termination output), are
referred to as asserted when they are high and negated when they are low.
MPC5125 Microcontroller Reference Manual, Rev. 2
Table
3-1.
NOTE
•
•
•
•
•
•
USB ULPI interface signals
ETH interface signals
CAN interface signals
J1850 interface signals
JTAG, test, system control signals
Clock signals
Figure
3-1. These functions are
3-1