MPC8536DS Freescale Semiconductor, MPC8536DS Datasheet - Page 601

• Manufacturer Part Number: MPC8536DS
• Description: BOARD DEV SYSTEM MPC8536E
• Manufacturer: Freescale Semiconductor
• Series: PowerQUICC III™r
• Type: MPUr

Specifications of MPC8536DS

• Contents: Board, Software and Documentation
• Processor Series: MPC85xx
• Core: e500
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 667 MHz
• Operating Supply Voltage: - 0.3 V to + 1.21 V
• Maximum Operating Temperature: + 105 C
• Data Ram Size: 32 KB
• Interface Type: SPI, USB
• Program Memory Type: DDR2, DDR3, SDRAM
• Core Size: 32 Bit
• Program Memory Size: 544KB
• Cpu Speed: 1.5GHz
• Digital Ic Case Style: BGA
• No. Of Pins: 783
• Supply Voltage Range: 0.95V To 1.05V
• Rohs Compliant: Yes
• For Use With/related Products: MPC8536
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.3.1.4
The I
which can be cleared by software. The MCF and RXAK bits are set at reset; all other I2CSR bits are
cleared on reset.
Table 11-7
Freescale Semiconductor
Bits
0
1
2
3
4
5
2
C status register, shown in
BCSTM Broadcast match
MAAS Addressed as a slave. When the value in I2CDR matches with the calling address, this bit is set. The
Name
SRW
MCF
MBB
MAL
describes the bit settings of the I2CSR.
Offset I
Reset
I
2
Data transfer. When one byte of data is transferred, the bit is cleared. It is set by the falling edge of the 9th
clock of a byte transfer.
0 Byte transfer in progress. MCF is cleared under the following conditions:
1 Byte transfer is completed
processor is interrupted, if I2CCR[MIEN] is set. Next, the processor must check the SRW bit and set
I2CCR[MTX] accordingly. Writing to the I2CCR automatically clears this bit.
0 Not addressed as a slave
1 Addressed as a slave
Bus busy. Indicates the status of the bus. When a START condition is detected, MBB is set. If a STOP
condition is detected, it is cleared.
0 I
1 I
Arbitration lost. Automatically set when the arbitration procedure is lost. Note that the device does not
automatically retry a failed transfer attempt.
0 Arbitration is not lost. Can only be cleared by software
1 Arbitration is lost
0 There has not been a broadcast match.
1 The calling address matches with the broadcast address instead of the programmed slave address. This
Slave read/write. When MAAS is set, SRW indicates the value of the R/W command bit of the calling address,
which is sent from the master.
0 Slave receive, master writing to slave
1 Slave transmit, master reading from slave. This bit is valid only when both of the following conditions are
By checking this bit, the processor can select slave transmit/receive mode according to the command of the
master.
C Status Register (I2CSR)
W
R
also sets if this I
true:
•When I2CDR is read in receive mode or
•When I2CDR is written in transmit mode
2
2
•A complete transfer occurred and no other transfers have been initiated.
•The I
I
2
2
C bus is idle
C bus is busy
MPC8536E PowerQUICC III Integrated Processor Reference Manual, Rev. 1
C1: 0x00C
C2: 0x10C
MCF
0
1
2
C interface is configured as a slave and has an address match.
MAAS
2
0
1
C drives an address of all 0s and broadcast mode is enabled.
Figure 11-5. I
Figure
Table 11-7. I2CSR Field Descriptions
MBB
11-5, is read only with the exception of the MIF and MAL bits,
0
2
2
C Status Register (I2CSR)
MAL
0
3
Description
BCSTM
0
4
SRW
0
5
MIF
0
6
Access: Mixed
RXAK
1
7
I
2
C Interfaces
11-9