MPC8308VMAGD Freescale Semiconductor, MPC8308VMAGD Datasheet - Page 402

• Manufacturer Part Number: MPC8308VMAGD
• Description: MPU POWERQUICC II PRO 473MAPBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC8308VMAGD

• Processor Type: MPC83xx PowerQUICC II Pro 32-Bit
• Speed: 400MHz
• Voltage: 1V
• Mounting Type: Surface Mount
• Package / Case: 473-MAPBGA
• Product: Network Processor
• Data Rate: 256 bps
• Frequency: 400 MHz
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Supply Current (max): 5 uA
• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: 0 C
• Interface: I2C, JTAG, SPI
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Enhanced Local Bus Controller
Table 10-13
10.3.1.7
The special operation initiation register (LSOR), shown in
special operation on the indicated bank. Writing to LSOR activates a special operation on bank
LSOR[BANK] provided that the bank is valid and controlled by a memory controller whose mode OP field
is set to a value other than ‘normal operation.’ If eLBC is currently busy with a memory transaction,
writing LSOR completes immediately, but the special operation request is queued until eLBC can service
it. To avoid race conditions between software and a busy eLBC, registers that affect currently running
special operation and LSOR must not be re-written before a pending special operation has been completed.
The UPM and FCM have different indications of when such special operations are completed. The
behavior of eLBC is unpredictable if special operation modes are altered between LSOR being written and
the relevant memory controller completing that access.
UPM special operation modes are set in registers MxMR[OP], see
Registers (MxMR).”
10-22
16–23
24–31
Offset 0x0_5088
Offset 0x0_5088
Reset
Reset
0–31
8–15
Bits
0–7
W
W
R
R
0
0
Name
AS3
AS2
AS1
AS0
D
describes MDR[D].
Special Operation Initiation Register (LSOR)
In UPM mode, D is the data to be read or written into the RAM array when a write or read command is
supplied to the UPM (M x MR[OP] = 01 or M x MR[OP] = 10).
In FCM mode, AS3 is the fourth byte of address sent by a custom address write operation, or the fourth byte
of data read from a read status operation.
In FCM mode, AS2 is the third byte of address sent by a custom address write operation, or the third byte of
data read from a read status operation.
In FCM mode, AS1 is the second byte of address sent by a custom address write operation, or the second
byte of data read from a read status operation.
In FCM mode, AS0 is the first byte of address sent by a custom address write operation, or the first byte of
data read from a read status operation.
AS3
FCM special operation modes are set in FMR[OP], see
MPC8308 PowerQUICC II Pro Processor Reference Manual, Rev. 0
Figure 10-10. FCM Data Register in FCM Mode (MDR)
Figure 10-9. UPM Data Register in UPM Mode (MDR)
7
8
Table 10-13. MDR Field Description
AS2
All zeros
All zeros
15 16
Description
D
Figure
10-11, is used by software to trigger a
AS1
Section 10.3.1.4, “UPM Mode
Section 10.3.1.17, “Flash
23 24
Freescale Semiconductor
Access: Read/Write
Access: Read/Write
AS0
31
31