MCF51EM256CLL Freescale Semiconductor, MCF51EM256CLL Datasheet - Page 269

• Manufacturer Part Number: MCF51EM256CLL
• Description: IC MCU 32BIT 256KB FLASH 100LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCF51EMr

Specifications of MCF51EM256CLL

• Core Processor: Coldfire V1
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LCD, LVD, PWM, WDT
• Number Of I /o: 63
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: MCF51EM
• Core: ColdFire V1
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: RS-232, LIN
• Maximum Clock Frequency: 50 MHz
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JLINK-CF-BDM26, EWCF
• Development Tools By Supplier: DEMOEM
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

In FLL bypassed external mode, the ICSOUT clock is derived from the external reference clock source.
The FLL clock is controlled by the external reference clock, and the FLL loop locks the FLL frequency to
the FLL factor times the external reference frequency, as selected by the RDIV bits, so that the ICSLCLK
will be available for BDC communications, and the external reference clock is enabled.
11.4.1.6
The FLL bypassed external low power (FBELP) mode is entered when all the following conditions occur:
In FLL bypassed external low power mode, the ICSOUT clock is derived from the external reference clock
source and the FLL is disabled. The ICSLCLK will be not be available for BDC communications. The
external reference clock source is enabled.
11.4.1.7
Stop mode is entered whenever the MCU enters a STOP state. In this mode, all ICS clock signals are static
except in the following cases:
ICSIRCLK will be active in stop mode when all the following conditions occur:
OSCOUT will be active in stop mode when all the following conditions occur:
11.4.2
The IREF bit can be changed at anytime, but the actual switch to the newly selected clock is shown by the
IREFST bit. When switching between FLL engaged internal (FEI) and FLL engaged external (FEE)
modes, the FLL begins locking again after the switch is completed.
The CLKS bits can also be changed at anytime, but the actual switch to the newly selected clock is shown
by the CLKST bits. If the newly selected clock is not available, the previous clock remains selected.
The DRS bits can be changed at anytime except when LP bit is 1. If the DRS bits are changed while in
FLL engaged internal (FEI) or FLL engaged external (FEE), the bus clock remains at the previous DCO
range until the new DCO starts. When the new DCO starts the bus clock switches to it. After switching to
the new DCO the FLL remains unlocked for several reference cycles. Once the selected DCO startup time
is over, the FLL is locked. The completion of the switch is shown by the DRST bits.
Freescale Semiconductor
•
•
•
•
•
•
•
CLKS bits are written to 10.
IREFS bit is written to 0.
BDM mode is not active and LP bit is written to 1.
IRCLKEN bit is written to 1.
IREFSTEN bit is written to 1.
ERCLKEN bit is written to 1.
EREFSTEN bit is written to 1.
Mode Switching
FLL Bypassed External Low Power (FBELP)
Stop
MCF51EM256 Series ColdFire Integrated Microcontroller Reference Manual, Rev. 8
Internal Clock Source (ICS)
11-15