MPC8536E-ANDROID Freescale Semiconductor, MPC8536E-ANDROID Datasheet - Page 883

• Manufacturer Part Number: MPC8536E-ANDROID
• Description: HARDWARE/SOFTWARE ANDROID OS
• Manufacturer: Freescale Semiconductor
• Series: PowerQUICC ™r
• Type: MPUr

Specifications of MPC8536E-ANDROID

• Contents: Board
• For Use With/related Products: MPC8536
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

14.5.4.2.2
Once synchronization is acquired, ordered_sets are decoded. If Configuration ordered_sets are received,
the eTSEC decodes the two octet data field and the sixteen-bit Configuration data is stored and used to
Auto-Negotiate with the link partner. in the Receive Configuration Register (RXCR[15:0]) an internal
register used to receive all the link partners informations and used to compare to local ability during
negotiation. Not visible to user. If, during Auto-Negotiation an invalid symbol is detected,
Auto-Negotiation re-starts. After Auto-Negotiation is completed the TBI MII Status Register SR[AN
done] in set. In this mode, packets may be received from the link partner.
14.5.4.3
This section describes the TBI MII registers. All of the TBI registers are 16 bits wide. The TBI registers
are accessed at the offset of the TBI physical address. The eTSEC’s TBI physical address is stored in the
TBIPA register. Writing to the TBI registers is performed in a way similar to writing to an external PHY,
using the MII management interface. Using TBIPA in place of the PHY address, in the MIIMADD[PHY
Address] field, and setting the MIIMADD[Register Address] to the appropriate address offset that
corresponds to the register that one wants to read or write (see
MIIMCOM[read cycle]) or write (writing to MIIMCON[PHY control]) to the TBI block. Refer to the TBI
physical address register in
MII register set in
registers and are only used for test and control of the eTSEC TBI block. The TBI’s TBI control register
(TBI) is for configuring the eTSEC ten-bit interface block. However, because this TBI block has an MII
management interface (just like any other PHY), it has an IEEE 802.3 register called the control register
(CR).
Freescale Semiconductor
1
0x02–0x03
R = Read-only, WO = Write Only, R/W = Read and Write, LH = Latches High, LL = Latches Low,
SC = Self-clearing,
Address
Offset
0x0F
0x00
0x01
0x04
0x05
0x06
0x07
0x08
0x10
0x11
TBI MII Set Register Descriptions
Auto-Negotiation for 1000BASE-X
Table
MPC8536E PowerQUICC III Integrated Processor Reference Manual, Rev. 1
Control (CR)
Status (SR)
Reserved
AN advertisement (ANA)
AN link partner base page ability
(ANLPBPA)
AN expansion (ANEX)
AN next page transmit (ANNPT)
AN link partner ability next page
(ANLPANP)
Extended status (EXST)
Jitter diagnostics (JD)
TBI control (TBICON)
14-130. Notice that jitter diagnostics and TBI control are not IEEE 802.3 required
TEN-BIT INTERFACE (TBI) REGISTERS
Section 14.5.3.1, “eTSEC General Control and Status
Table 14-130. TBI MII Register Set
Name
R, LH, LL
Access
R/W, R
RW, R
R, LH
R/W
R/W
R/W
R
R
R
R
Table
1
14-130), the user can read (set
Enhanced Three-Speed Ethernet Controllers
2 bytes
16 bits
16 bits
16 bits
16 bits
16 bits
16 bits
16 bits
16 bits
16 bits
16 bits
Size
14.5.4.3.10/14-145
14.5.4.3.1/14-136
14.5.4.3.2/14-137
14.5.4.3.2/14-137
14.5.4.3.4/14-140
14.5.4.3.5/14-141
14.5.4.3.6/14-141
14.5.4.3.7/14-142
14.5.4.3.8/14-143
14.5.4.3.9/14-144
Registers,” and the TBI
Section/page
14.5.4/14-133
—
14-135