MPC561MZP56 Freescale, MPC561MZP56 Datasheet - Page 330

MPC561MZP56

Manufacturer Part Number
MPC561MZP56
Description
Manufacturer
Freescale
Datasheet

Specifications of MPC561MZP56

Cpu Family
MPC56x
Device Core
PowerPC
Device Core Size
32b
Frequency (max)
56MHz
Interface Type
QSPI/SCI/SPI/UART
Total Internal Ram Size
32KB
# I/os (max)
56
Number Of Timers - General Purpose
22
Operating Supply Voltage (typ)
2.6/5V
Operating Supply Voltage (max)
2.7/5.25V
Operating Supply Voltage (min)
2.5/4.75V
On-chip Adc
2(32-chx10-bit)
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 125C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Pin Count
388
Package Type
BGA
Program Memory Type
ROMLess
Program Memory Size
Not Required
Lead Free Status / RoHS Status
Not Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MPC561MZP56
Manufacturer:
FREESCALE
Quantity:
852
Part Number:
MPC561MZP56
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Part Number:
MPC561MZP56
Manufacturer:
FREESCALE
Quantity:
852
Company:
Part Number:
MPC561MZP56
Quantity:
13
Part Number:
MPC561MZP56R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Clocks and Power Control
During the power down sequence PORESET needs to be asserted while VDD, NVDDL, and QVDDL are
at a voltage greater than or equal to 2.5 V. Below this voltage the power supply chip can be turned off.
If the turn-off voltage of the power supply chip is greater than 0.74 V for the 2.6-V supply and greater than
0.8 V for the 5-V supply, then the circuitry inside the MPC561/MPC563 will act as a load to the respective
supply and will discharge the supply line down to these values. Since the 2.6-V logic represents a larger
load to the supply chip, the 2.6-V supply line will decay faster than the 5-V supply line.
8-28
VFLASH (5 V)
1
2
3
4
5
VDDA, VRH
IRAMSTBY
VDD, NVVL,
QVDDL
VDDH ≥ QVDDL - 0.5 V
VDDA can lag VDDH, and VDDSYN can lag QVDDL, but both must be at a valid level before resets are negated.
If keep-alive functions are NOT used, then when system power is on: KAPWR = QVDDL ± 0.1 V; KAPWR ≤ 2.7 V
If keep-alive functions ARE used, then KAPWR = QVDDL = NVDDL = 2.6 V ± 0.1 V when system power is on
KAPWR = 2.6 V ± 0.1 V when system power is off. IRAMSTBY should be powered prior to the other supplies. If
IRAMSTBY is powered at the same time as the other supplies, it should be allowed to stabilize before PORESET
is negated. Normal system power is defined as QVDDL = VDD = VDDF = VDDSYN = KAPWR = 2.6 ± 0.1 V and
VDDA = VDDH = VFLASH = 5.0 ± 0.25 V. Flash programming requirements are the same as normal system
power. VFLASH should always be 5.0 ± 0.25 V. Note: Flash is not implemented on the MPC561.
Do not hold the 2.6-V supplies at ground while VDDH/VDDA is ramping to 5 V.
If 5 V is applied before the 2.6-V supply, all 5-V outputs will be in indeterminate states until the 2.6-V supply
reaches a level that allows reset to be distributed throughout the device If 5 V is applied before the 2.6-V supply,
all 5-V outputs will be in indeterminate states until the 2.6-V supply reaches a level that allows reset to be
distributed throughout the device
PORESET
VDDSYN
HRESET
KAPWR
VDDH
Figure 8-14. No Standby, No KAPWR, All System Power-On/Off
MPC561/MPC563 Reference Manual, Rev. 1.2
Power On
See Note 1.
Operating
See Note 2.
Power Off
Freescale Semiconductor

Related parts for MPC561MZP56