MPC561MZP56 Freescale, MPC561MZP56 Datasheet - Page 766
MPC561MZP56
Manufacturer Part Number
MPC561MZP56
Description
Manufacturer
Freescale
Datasheet
1.MPC561MZP56.pdf
(1420 pages)
Specifications of MPC561MZP56
Cpu Family
MPC56x
Device Core
PowerPC
Device Core Size
32b
Frequency (max)
56MHz
Interface Type
QSPI/SCI/SPI/UART
Total Internal Ram Size
32KB
# I/os (max)
56
Number Of Timers - General Purpose
22
Operating Supply Voltage (typ)
2.6/5V
Operating Supply Voltage (max)
2.7/5.25V
Operating Supply Voltage (min)
2.5/4.75V
On-chip Adc
2(32-chx10-bit)
Instruction Set Architecture
RISC
Operating Temp Range
-40C to 125C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Pin Count
388
Package Type
BGA
Program Memory Type
ROMLess
Program Memory Size
Not Required
Lead Free Status / RoHS Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MPC561MZP56
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
Company:
Part Number:
MPC561MZP56R2
Manufacturer:
Freescale Semiconductor
Quantity:
10 000
- Current page: 766 of 1420
- Download datasheet (11Mb)
Modular Input/Output Subsystem (MIOS14)
The output flip-flop is set when a match occurs on channel A. The output flip-flop is reset when a match
occurs on channel B. The polarity of the output signal is selected by the EDPOL bit. The output flip-flop
level can be obtained at any time by reading the PIN bit.
If subsequent enabled output compares occur on channels A and B, the output pulses continue to be output,
regardless of the state of the FLAG bit.
At any time, the FORCA and FORCB bits allow the software to force the output flip-flop to the level
corresponding to a comparison on channel A or B, respectively.
Totem pole or open-drain output circuit configurations can be selected using the WOR bit in the
MDASMSCR register.
17.9.3.5.1
The single shot output pulse operation is selected by writing the leading edge value of the desired pulse to
data register A and the trailing edge value to data register B. A single pulse will be output at the desired
time, thereby disabling the comparators until new values are written to the data registers. To generate a
single shot output pulse, the OCB mode should be used to only generate a flag on the B match.
In this mode, registers A and B2 are accessible to the user software (at consecutive addresses).
Figure 17-19
17-34
provides an example of how the MDASM can be used to generate a single output pulse.
The FLAG line is not affected by these ‘force’ operations.
If both channels are loaded with the same value, the output flip-flop
provides a logic zero level output and the flag bit is still set on the match.
16-bit counter bus compare only occurs when the 16-bit counter bus is
updated.
Single Shot Output Pulse Operation
MPC561/MPC563 Reference Manual, Rev. 1.2
NOTE
NOTE
NOTE
Freescale Semiconductor
Related parts for MPC561MZP56
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MPC5 1K0 5%
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
MPC5 500R 5%
Manufacturer:
TE Connectivity
Datasheet:
Part Number:
Description:
MPC5 5K0 5%
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
MPC5 5R0 5%
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
MPC5 50K 5%
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
MPC5 1R0 5%
Manufacturer:
Tyco Electronics
Datasheet:
Part Number:
Description:
TOWER ELEVATOR BOARDS HARDWARE
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SERIAL I/O HARDWARE
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
LCD MODULE FOR TWR SYSTEM
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
DAUGHTER LCD WVGA I.MX51
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
TOWER SYSTEM BOARD MPC5125
Manufacturer:
Freescale Semiconductor
Datasheet: