MPC561MZP56 Freescale, MPC561MZP56 Datasheet - Page 1308

• Manufacturer Part Number: MPC561MZP56
• Manufacturer: Freescale

Specifications of MPC561MZP56

• Cpu Family: MPC56x
• Device Core: PowerPC
• Device Core Size: 32b
• Frequency (max): 56MHz
• Interface Type: QSPI/SCI/SPI/UART
• Total Internal Ram Size: 32KB
• # I/os (max): 56
• Number Of Timers - General Purpose: 22
• Operating Supply Voltage (typ): 2.6/5V
• Operating Supply Voltage (max): 2.7/5.25V
• Operating Supply Voltage (min): 2.5/4.75V
• On-chip Adc: 2(32-chx10-bit)
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 388
• Package Type: BGA
• Program Memory Type: ROMLess
• Program Memory Size: Not Required
• Lead Free Status / RoHS Status: Not Compliant

66-MHz Electrical Characteristics
Functional operating conditions are given in
maximum ratings are stress ratings only, and functional operation at the maximum is not guaranteed. Stress
beyond those listed may affect device reliability or cause permanent damage to the device.
G-2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
19a Operating Temperature Range – Ambient
17
18
19
20
21
22
23
24
For internal digital supply of V
2.6 volt supply pins can withstand up to 3.6 volts for acumulative time of 24 hours over the lifetime of the device.
During operation the value of V
These power supplies are available on MPC563 and MPC564 only.
Maximum average current into the IRAMSTBY pin must be < 1.75mA.
V
All 2.6-V input-only pins are 5-V tolerant.
Note that long term reliability may be compromised if 2.6-V output drivers drive a node which has been previously
pulled to >3.1 V by an external component. HRESET and SRESET are fully 5-V compatible.
6.35 V on 5-V only pins (all QADC, all TPU, all QSMCM and the following MIOS pins: MDA[11:15], MDA[27:31],
MPWM16, MPIO32B[7:9]/MPWM[20:21], MPIO32B11/C_CNRX0, MPIO32B12/C_CNTX0 ). Internal structures hold
the input voltage below this maximum voltage on all of these pins, except the QSMCM RXD1/QPI1 and
RXD2/QPI2/C_CNRX0 pins, if the maximum injection current specification is met (1 mA for all pins; exception: 3 mA
on QADC pins) and VDDH is within Operating Voltage specifications (see specification 43 in
The RXD1/QGPI1 and RXD2/GPI2 pins do not have clamp diodes to VDDH. Voltage must be limited to less than 6.5
volts on these 2 pins to prevent damage.
Maximum continuous current on I/O pins provided the overall power dissipation is below the power dissipation of the
package. Proper operation is not guaranteed at this condition.
Condition applies to one pin at a time.
Transitions within the limit do not affect device reliability or cause permanent damage. Exceeding limit may cause
permanent conversion error on stressed channels and on unstressed channels.
Maximum transient current per ISO7637.
Maximum operating temperature on any solder ball in outer four rows of solder balls on the package. These rows are
referred to as “Perimeter Balls” to distinguish them from the balls in the center of the package.
Solder profile per CDF-AEC-Q100, current revision.
Moisture sensitivity per JEDEC test method J-STD-020-A (April 1999).
DDA
Maximum Input Current per pin
QADC Maximum Input Current per Pin
Operating Temperature Range – Ambient
(Packaged), M temperature range.
(Packaged), C temperature range.
Operating Temperature Range – Solder Ball
(Packaged any perimeter solder ball)
Junction Temperature Range
Storage Temperature Range
Maximum Solder Temperature
Moisture Sensitivity Level
=5.0 V
±
5%.
Table G-1. Absolute Maximum Ratings (VSS = 0V) (continued)
Rating
DDL
16
FLASH
MPC561/MPC563 Reference Manual, Rev. 1.2
= 2.6-V typical.
15
10, 11, 12
must be 5.0 V
14
Section G.6, “DC Electrical
±
5%
Symbol
T
T
MSL
I
T
I
MAX
MA
T
T
T
STG
SDR
SB
A
A
J
Min. Value
-25
-25
(T
(T
(T
-40
-40
-40
-40
-55
—
—
L
L
L
13
13
)
)
)
Characteristics.” Absolute
Max. Value
+125
+135
+150
+150
25
25
(T
(T
(T
+85
235
3
H
H
H
13
13
)
)
)
Table
Freescale Semiconductor
G-4). Exception:
Unit
mA
mA
°C
°C
°C
°C
°C
°C
—