HD6417727F100CV Renesas Electronics America, HD6417727F100CV Datasheet - Page 208

• Manufacturer Part Number: HD6417727F100CV
• Description: SH3-DSP, LEAD FREE
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7700r

Specifications of HD6417727F100CV

• Core Processor: SH-3 DSP
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: FIFO, SCI, SIO, SmartCard, USB
• Peripherals: DMA, LCD, POR, WDT
• Number Of I /o: 104
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.6 V ~ 2.05 V
• Data Converters: A/D 6x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 240-QFP Exposed Pad, 240-eQFP, 240-HQFP
• Cpu Family: SuperH
• Device Core Size: 32b
• Frequency (max): 100MHz
• Interface Type: SCI/USB
• Program Memory Size: Not Required
• Total Internal Ram Size: 16KB
• # I/os (max): 104
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 2.05/3.6V
• Operating Supply Voltage (min): 1.6/2.6V
• On-chip Adc: 6-chx10-bit
• On-chip Dac: 2-chx8-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -20C to 75C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 240
• Package Type: HQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Compliant

Section 5 Cache
Address Array: The V bit indicates whether the entry data is valid. When the V bit is 1, data is
valid; when 0, data is not valid. The U bit indicates whether the entry has been written to in write-
back mode. When the U bit is 1, the entry has been written to; when 0, it has not. The address tag
holds the physical address used in the external memory access. It is composed of 22 bits (address
bits 31 to 10) used for comparison during cache searches.
In the SH7727, the top three of 32 physical address bits are used as shadow bits (see section 12,
Bus State Controller (BSC)), and therefore in a normal replace operation the top three bits of the
tag address are cleared to 0.
The V and U bits are initialized to 0 by a power-on reset, but are not initialized by a manual reset.
The tag address is not initialized by either a power-on or manual reset.
Data Array: Holds a 16-byte instruction or data. Entries are registered in the cache in line units
(16 bytes). The data array is not initialized by a power-on or manual reset.
LRU: With the 4-way set associative system, up to four instructions or data with the same entry
address (address bits 11 to 4) can be registered in the cache. When an entry is registered, the LRU
shows which of the four ways it is recorded in. There are six LRU bits, controlled by hardware. A
least-recently-used (LRU) algorithm is used to select the way.
In normal operation, four ways are used as cache and six LRU bits indicate the way to be replaced
(table 5.2). If a bit pattern other than those listed in table 5.2 is set in the LRU bits by software, the
Rev.6.00 Mar. 27, 2009 Page 150 of 1036
REJ09B0254-0600
Entry 255
Entry 0
Entry 1
.
.
.
.
.
.
24 (1 + 1 + 22) bits
V U Tag address
Address array (ways 0 to 3)
Figure 5.1 Cache Structure
255
0
1
.
.
.
.
.
.
LW0
LW0−LW3: Longword data 0 to 3
128 (32 × 4) bits
LW1
LW2
Data array (ways 0 to 3)
LW3
255
0
1
.
.
.
.
.
.
LRU
6 bits