DS72011RB120FPV Renesas Electronics America, DS72011RB120FPV Datasheet - Page 174

• Manufacturer Part Number: DS72011RB120FPV
• Description: IC SH7201 MPU ROMLESS 176LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7200r

Specifications of DS72011RB120FPV

• Core Size: 32-Bit
• Core Processor: SH-2A
• Speed: 120MHz
• Connectivity: CAN, EBI/EMI, FIFO, I²C, SCI, Serial Sound
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 104
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 70°C
• Package / Case: 176-LQFP
• No. Of I/o's: 109
• Ram Memory Size: 32KB
• Cpu Speed: 120MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -20°C To +70°C
• Embedded Interface Type: I2C, SSI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K572011S000BE - KIT STARTER FOR SH7201HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Section 6 Interrupt Controller (INTC)
6.6
6.6.1
The sequence of interrupt operations is described below. Figure 6.2 shows the operation flow.
1. The interrupt request sources send interrupt request signals to the interrupt controller.
2. The interrupt controller selects the highest-priority interrupt from the interrupt requests sent,
3. The priority level of the interrupt selected by the interrupt controller is compared with the
4. The CPU detects the interrupt request sent from the interrupt controller when the CPU decodes
5. The start address of the interrupt exception service routine is fetched from the exception
6. The status register (SR) is saved onto the stack, and the priority level of the accepted interrupt
7. The program counter (PC) is saved onto the stack.
8. The CPU jumps to the fetched start address of the interrupt exception service routine and starts
Notes: The interrupt source flag should be cleared in the interrupt handler. After clearing the
Page 146 of 1190
following the priority levels set in interrupt priority registers 01, 02, and 05 to 16 (IPR01,
IPR02, and IPR05 to IPR16). Lower priority interrupts are ignored
have the same priority level or if multiple interrupts occur within a single IPR, the interrupt
with the highest priority is selected, according to the default priority and IPR setting unit
internal priority shown in table 6.4.
interrupt level mask bits (I3 to I0) in the status register (SR) of the CPU. If the interrupt
request priority level is equal to or less than the level set in bits I3 to I0, the interrupt request is
ignored. If the interrupt request priority level is higher than the level in bits I3 to I0, the
interrupt controller accepts the interrupt and sends an interrupt request signal to the CPU.
the instruction to be executed. Instead of executing the decoded instruction, the CPU starts
interrupt exception handling (figure 6.4).
handling vector table corresponding to the accepted interrupt.
is copied to bits I3 to I0 in SR.
executing the program. The jump that occurs is not a delayed branch.
* Interrupt requests that are designated as edge-sensing are held pending until the
interrupt source flag, "time from occurrence of interrupt request until interrupt controller
identifies priority, compares it with mask bits in SR, and sends interrupt request signal to
CPU" shown in table 6.5 is required before the interrupt source sent to the CPU is actually
cancelled. To ensure that an interrupt request that should have been cleared is not
inadvertently accepted again, read the interrupt source flag after it has been cleared, and
then execute an RTE instruction.
Operation
Interrupt Operation Sequence
interrupt requests are accepted. IRQ interrupts, however, can be cancelled by accessing
the IRQ interrupt request register (IRQRR). For details, see section 6.4.4, IRQ
Interrupts.
Interrupts held pending due to edge-sensing are cleared by a power-on reset or in deep
standby mode.
*
. If two of these interrupts
R01UH0026EJ0300 Rev. 3.00
SH7201 Group
Sep 24, 2010