DS72011RB120FPV Renesas Electronics America, DS72011RB120FPV Datasheet - Page 164

• Manufacturer Part Number: DS72011RB120FPV
• Description: IC SH7201 MPU ROMLESS 176LQFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7200r

Specifications of DS72011RB120FPV

• Core Size: 32-Bit
• Core Processor: SH-2A
• Speed: 120MHz
• Connectivity: CAN, EBI/EMI, FIFO, I²C, SCI, Serial Sound
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 104
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 70°C
• Package / Case: 176-LQFP
• No. Of I/o's: 109
• Ram Memory Size: 32KB
• Cpu Speed: 120MHz
• Digital Ic Case Style: LQFP
• Supply Voltage Range: 3V To 3.6V
• Operating Temperature Range: -20°C To +70°C
• Embedded Interface Type: I2C, SSI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: R0K572011S000BE - KIT STARTER FOR SH7201HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

SH7201 Group
Section 6 Interrupt Controller (INTC)
As every source is assigned a different interrupt vector, the source does not need to be identified in
the exception service routine. A priority level in a range from 0 to 15 can be set for each module
by interrupt priority registers 05 to 16 (IPR05 to IPR16). The on-chip peripheral module interrupt
exception handling sets the I3 to I0 bits in SR to the priority level of the accepted on-chip
peripheral module interrupt.
6.5
Interrupt Exception Handling Vector Table and Priority
Table 6.4 lists interrupt sources and their vector numbers, vector table address offsets, and
interrupt priorities.
Each interrupt source is allocated a different vector number and vector table address offset. Vector
table addresses are calculated from the vector numbers and vector table address offsets. In
interrupt exception handling, the exception service routine start address is fetched from the vector
table indicated by the vector table address. For details of calculation of the vector table address,
see table 5.4, Calculating Exception Handling Vector Table Addresses, in section 5, Exception
Handling.
The priorities of IRQ interrupts, PINT interrupts, and on-chip peripheral module interrupts can be
set freely between 0 and 15 for each pin or module by setting interrupt priority registers 01, 02,
and 05 to 16 (IPR01, IPR02, and IPR05 to IPR16). However, if two or more interrupts specified
by the same IPR among IPR05 to IPR16 occur, the priorities are defined as shown in the IPR
setting unit internal priority of table 6.4, and the priorities cannot be changed. A power-on reset
assigns priority level 0 to IRQ interrupts, PINT interrupts, and on-chip peripheral module
interrupts. If the same priority level is assigned to two or more interrupt sources and interrupts
from those sources occur simultaneously, they are processed by the default priorities indicated in
table 6.4.
Page 136 of 1190
R01UH0026EJ0300 Rev. 3.00
Sep 24, 2010