LPC1767FBD100,551 NXP Semiconductors, LPC1767FBD100,551 Datasheet - Page 178

• Manufacturer Part Number: LPC1767FBD100,551
• Description: IC ARM CORTEX MCU 512K 100-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1767FBD100,551

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 100MHz
• Connectivity: Ethernet, I²C, IrDA, Microwire, SPI, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 70
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Processor Series: LPC17
• Core: ARM Cortex M3
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB1760, MCB1760U, MCB1760UME
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4967; 935289808551

NXP Semiconductors
10.17 Interrupts
UM10360
User manual
10.16.2 AHB interface
10.17.1 Direct Memory Access (DMA)
To transmit a packet the software driver has to set up the appropriate Control registers
and a descriptor to point to the packet data buffer before transferring the packet to
hardware by incrementing the TxProduceIndex register. After transmission, hardware will
increment TxConsumeIndex and optionally generate an interrupt.
The hardware will receive packets from the PHY and apply filtering as configured by the
software driver. While receiving a packet the hardware will read a descriptor from memory
to find the location of the associated receiver data buffer. Receive data is written in the
data buffer and receive status is returned in the receive descriptor status word. Optionally
an interrupt can be generated to notify software that a packet has been received. Note
that the DMA manager will prefetch and buffer up to three descriptors.
The registers of the Ethernet block connect to an AHB slave interface to allow access to
the registers from the CPU.
The AHB interface has a 32-bit data path, which supports only word accesses and has an
address aperture of 4 kB.
All AHB write accesses to registers are posted except for accesses to the IntSet, IntClear
and IntEnable registers. AHB write operations are executed in order.
If the PowerDown bit of the PowerDown register is set, all AHB read and write accesses
will return a read or write error except for accesses to the PowerDown register.
Bus Errors
The Ethernet block generates errors for several conditions:
The Ethernet block has a single interrupt request output to the CPU (via the NVIC).
The interrupt service routine must read the IntStatus register to determine the origin of the
interrupt. All interrupt statuses can be set by software writing to the IntSet register;
statuses can be cleared by software writing to the IntClear register.
The transmit and receive data paths can only set interrupt statuses, they cannot clear
statuses. The SoftInt interrupt cannot be set by hardware and can be used by software for
test purposes.
Descriptor arrays
•
•
The AHB interface will return a read error when there is an AHB read access to a
write-only register; likewise a write error is returned when there is an AHB write
access to the read-only register. An AHB read or write error will be returned on AHB
read or write accesses to reserved registers. These errors are propagated back to the
CPU. Registers defined as read-only and write-only are identified in
If the PowerDown bit is set all accesses to AHB registers will result in an error
response except for accesses to the PowerDown register.
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 August 2010
Table 128
lists the registers of the Ethernet block.
Chapter 10: LPC17xx Ethernet
UM10360
© NXP B.V. 2010. All rights reserved.
Table
128.
178 of 840