pc87591l-n05 National Semiconductor Corporation, pc87591l-n05 Datasheet - Page 199
![no-image](/images/no-image-200.jpg)
pc87591l-n05
Manufacturer Part Number
pc87591l-n05
Description
Lpc Mobile Embedded Controller
Manufacturer
National Semiconductor Corporation
Datasheet
1.PC87591L-N05.pdf
(401 pages)
- Current page: 199 of 401
- Download datasheet (2Mb)
Revision 1.2
4.0 Embedded Controller Modules
4.14.4 ACM Operation
Reset
The ACM is initialized by core domain reset (Section 3.2 on page 61 describes the PC87591L-N05 reset events).
Upon reset, the ACM is disabled, with all interrupt sources masked and the over/under threshold select set to “below”. All
Event status bits are reset. The trigger division factor, as well as the data sampling delay, are set to their maximum value
(for the slowest ACM operation speed). The comparison threshold is set to zero.
All control, configuration and status registers are reset to their default values, as indicated in Section 4.14.5 on page 201.
Voltage Level Data Buffer registers and the Comparison Result register’s values are invalid until the first measurement oc-
curs (on each of them).
Sampling Delay
This delay separates between the new value being loaded into the D/A converter and the data being sampled into the Volt-
age Level Data Buffer registers and the Comparison Result register. Its value should be longer than the total time required
by the D/A output to settle (within 1/2 LSB of 6 bits) and the comparators to toggle their state.
The value set by SMPDLY field in ACMTIM register is expressed in terms of core CLK clock cycles. The maximum frequency
at which each delay may be used is specified in the register’s description.
Initializing the ACM
The ACM must be initialized before it is enabled and used. The following operations should be done:
After initializations are done, the ACM may be enabled by writing 1 to START bit in ACMCTS register.
Note: Setting any of the above bits/fields during ACM operation may cause unpredictable results.
• Select the ACM Mode Control by setting ACMMOD field in ACMCNF register.
• Enable interrupts are required using the following bits of ACMCNF register:
• Select Over or Under Threshold mode, using OVUNSEL bit in ACMCNF register.
• Set the data sampling delay using SMPDLY field in ACMTIM register.
• Select the low power trigger rate by setting T0DIV field in ACMTIM register.
• Select the Comparison Threshold Data for wake-up by setting THRSHD field in THRDAT register.
— Interrupt from End-of-Measurement Event Enable by setting INTEMEN bit.
— Interrupt from Over/Under Threshold Event Enable by setting INTOUEN bit.
Voltage Ratio to V
Figure 72. Level Data to Input Voltage Ratio Conversion
CC
62/64
63/64
(FS)
3/64
2/64
1/64
FS
0
0
1
(Continued)
2
3
199
. . . . .
62
63
(64)
Level Data
www.national.com
Related parts for pc87591l-n05
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![pc87591l](/images/no-image3.png)
Part Number:
Description:
Lpc Mobile Embedded Controllers
Manufacturer:
National Semiconductor Corporation
Datasheet:
![PC875](/photos/7/69/76943/425-8-dip_tmb.jpg)
Part Number:
Description:
PHOTOCOUPLER 2CH OUT 8-DIP
Manufacturer:
Sharp Microelectronics
Datasheet:
![mma1270keg](/images/no-image3.png)
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
![ADC12034](/images/no-image3.png)
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2350](/images/no-image3.png)
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2324](/images/no-image3.png)
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2301](/images/no-image3.png)
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![NDS8963](/images/no-image3.png)
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM1201](/images/no-image3.png)
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM3501TL-16](/images/no-image3.png)
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![AD9621](/images/no-image3.png)
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM2403](/images/no-image3.png)
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM592M](/images/no-image3.png)
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
![ADC10061](/images/no-image3.png)
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS36277TMX](/images/no-image3.png)
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet: