AT32UC3A364-ALUT Atmel, AT32UC3A364-ALUT Datasheet - Page 479

• Manufacturer Part Number: AT32UC3A364-ALUT
• Description: IC MCU 64KB FLASH 144LQFP
• Manufacturer: Atmel
• Series: AVR®32 UC3r

Specifications of AT32UC3A364-ALUT

• Core Processor: AVR
• Core Size: 32-Bit
• Speed: 66MHz
• Connectivity: EBI/EMI, I²C, IrDA, MMC, SPI, SSC, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, POR, WDT
• Number Of I /o: 110
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 128K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: AT32UC3x
• Core: AVR32
• Data Bus Width: 32 bit
• Data Ram Size: 96 KB
• Interface Type: IrDA/SCI/SCIF/UDI
• Maximum Clock Frequency: 66 MHz
• Number Of Timers: 3
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR32, EWAVR32-BL, KSK-EVK1100-PL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATEXTWIFI, ATEVK1104
• Minimum Operating Temperature: - 40 C
• Controller Family/series: AT32UC3A
• No. Of I/o's: 110
• Ram Memory Size: 64KB
• Cpu Speed: 66MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• For Use With: ATEVK1104 - KIT DEV/EVAL FOR AVR32 AT32UC3AATAVRONEKIT - KIT AVR/AVR32 DEBUGGER/PROGRMMRATEVK1100 - KIT DEV/EVAL FOR AVR32 AT32UC3A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Figure 23-11. Arbitration Cases
23.8.7
23.8.7.1
32072C–AVR32–2010/03
Data from a Master
TWI DATA transfer
Data from TWI
(DADR + W + START + Write THR)
Combined Transfers
ARBLST
A transfer is programmed
TWCK
Write Followed by Write
TWD
TWCK
TWD
CMDR and NCMDR may be used to generate longer sequences of connected transfers, since
generation of START and/or STOP conditions is programmable on a per-command basis.
Programming NCMDR with START=1 when the previous transfer was programmed with
STOP=0 will cause a REPEATED START on the bus. The ability to generate such connected
transfers allows arbitrary transfer lengths, since it is legal to program CMDR with both START=0
and STOP=0. If this is done in master receiver mode, the CMDR.ACKLAST bit must also be
controlled.
As for single data transfers, the TXRDY and RXRDY bits in the Status Register indicates when
data to transmit can be written to the THR, or when received data can be read from RHR. Trans-
fer of data to THR and from RHR can also be done automatically by DMA, see
Peripheral DMA Controller” on page 477
Consider the following transfer:
START, DADR+W, DATA+A, DATA+A, REPSTART, DADR+W, DATA+A, DATA+A, STOP.
To generate this transfer:
1. Program CMDR with START=1, STOP=0, DADR, NBYTES=2 and READ=0.
2. Program NCMDR with START=1, STOP=1, DADR, NBYTES=2 and READ=0.
3. Wait until SR.TXRDY==1, then write first data byte to transfer to THR.
4. Wait until SR.TXRDY==1, then write second data byte to transfer to THR.
S
S
S
1
1
1
Transfer is stopped
0 0
0
0 0
1
1 1
1 1
TWI stops sending data
Arbitration is lost
(DADR + W + START + Write THR)
Transfer is programmed again
Data from the master
Bus is busy
Transfer is kept
P
P
Bus is free
Bus is considered as free
Transfer is initiated
S
S
S
1
1
1
0
0 0
0
AT32UC3A3/A4
1
0
1 1
The master stops sending data
1 1
Arbitration is lost
Data from the TWI
”Using the
479