DF2134AFA20V Renesas Electronics America, DF2134AFA20V Datasheet - Page 129

• Manufacturer Part Number: DF2134AFA20V
• Description: IC H8S/2100 MCU FLASH 80QFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2100r

Specifications of DF2134AFA20V

• Core Processor: H8S/2000
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: IrDA, SCI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 58
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 80-QFP
• For Use With: 3DK2166 - DEV EVAL KIT H8S/2166
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Bit 7—Expanded Mode Enable (EXPE): Sets expanded mode. In mode 1, this bit is fixed at 1
and cannot be modified. In modes 2 and 3, this bit has an initial value of 0, and can be read and
written.
Bits 6 to 2—Reserved: These bits cannot be modified and are always read as 0.
Bits 1 and 0—Mode Select 1 and 0 (MDS1, MDS0): These bits indicate the input levels at pins
MD1 and MD0 (the current operating mode). Bits MDS1 and MDS0 correspond to MD1 and
MD0. MDS1 and MDS0 are read-only bits—they cannot be written to. The mode pin (MD1 and
MD0) input levels are latched into these bits when MDCR is read.
3.2.2
SYSCR is an 8-bit readable/writable register that performs selection of system pin functions, reset
source monitoring, interrupt control mode selection, NMI detected edge selection, supporting
module pin location selection, supporting module register access control, and RAM address space
control.
Only bits 7, 6, 3, 1, and 0 are described here. For a detailed description of these bits, refer also to
the description of the relevant modules (host interface, bus controller, watchdog timer, RAM,
etc.). For information on bits 5, 4, and 2, see section 5.2.1, System Control Register (SYSCR).
SYSCR is initialized to H'09 by a reset and in hardware standby mode. It is not initialized in
software standby mode.
Bit 7—Chip Select 2 Enable (CS2E): Specifies the location of the host interface control pin
(CS2). For details, see section 17, Host Interface. The H8S/2134 Group does not incorporate a
host interface, so do not set this bit to 1 in the H8S/2134 Group.
Bit 7
EXPE
0
1
Bit
Initial value
Read/Write
System Control Register (SYSCR)
Description
Single chip mode is selected
Expanded mode is selected
CS2E
R/W
7
0
IOSE
R/W
6
0
INTM1
R
5
0
INTM0
R/W
4
0
Rev. 4.00 Jun 06, 2006 page 73 of 1004
XRST
R
3
1
Section 3 MCU Operating Modes
NMIEG
R/W
2
0
R/W
HIE
REJ09B0301-0400
1
0
RAME
R/W
0
1