UPD78F1174AGF-GAT-AX Renesas Electronics America, UPD78F1174AGF-GAT-AX Datasheet - Page 563

• Manufacturer Part Number: UPD78F1174AGF-GAT-AX
• Description: MCU 16BIT 78K0R/KX3 128-LQFP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Kx3r

Specifications of UPD78F1174AGF-GAT-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: 3-Wire SIO, EBI/EMI, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 111
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

14.3 Registers to Controlling Serial Interface IIC0
Address: F00F0H
Serial interface IIC0 is controlled by the following eight registers.
(1) Peripheral enable register 0 (PER0)
(2) IIC control register 0 (IICC0)
Symbol
PER0
• Peripheral enable register 0 (PER0)
• IIC control register 0 (IICC0)
• IIC flag register 0 (IICF0)
• IIC status register 0 (IICS0)
• IIC clock select register 0 (IICCL0)
• IIC function expansion register 0 (IICX0)
• Port mode register 6 (PM6)
• Port register 6 (P6)
PER0 is used to enable or disable use of each peripheral hardware macro. Clock supply to a hardware macro
that is not used is stopped in order to reduce the power consumption and noise.
When serial interface IIC0 is used, be sure to set bit 4 (IIC0EN) of this register to 1.
PER0 can be set by a 1-bit or 8-bit memory manipulation instruction.
Reset signal generation clears this register to 00H.
Caution
This register is used to enable/stop I
IICC0 can be set by a 1-bit or 8-bit memory manipulation instruction. However, set the SPIE0, WTIM0, and
ACKE0 bits while IICE0 bit = 0 or during the wait period. These bits can be set at the same time when the
IICE0 bit is set from “0” to “1”.
Reset signal generation clears this register to 00H.
RTCEN
IIC0EN
<7>
0
1
After reset: 00H
When setting serial interface IIC0, be sure to set IIC0EN to 1 first. If IIC0EN = 0, writing to a
control register of serial interface IIC0 is ignored, and, even if the register is read, only the
default value is read (except for port mode register 6 (PM6) and port register 6 (P6)).
Stops supply of input clock.
• SFR used by serial interface IIC0 cannot be written.
• Serial interface IIC0 is in the reset status.
Supplies input clock.
• SFR used by serial interface IIC0 can be read/written.
Figure 14-5. Format of Peripheral Enable Register 0 (PER0)
DACEN
<6>
R/W
CHAPTER 14 SERIAL INTERFACE IIC0
ADCEN
2
<5>
C operations, set wait timing, and set other I
User’s Manual U18432EJ5V0UD
Control of serial interface IIC0 input clock
IIC0EN
<4>
SAU1EN
<3>
SAU0EN
<2>
2
C operations.
TAU1EN
<1>
TAU0EN
<0>
561