ATSAM3S1BA-AU Atmel, ATSAM3S1BA-AU Datasheet - Page 811

• Manufacturer Part Number: ATSAM3S1BA-AU
• Description: IC MCU 32BIT 64KB FLASH 64LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S1BA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 47
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 10x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 47
• Ram Memory Size: 16KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

35.11 HSMCI Boot Operation Mode
35.11.1
6500C–ATARM–8-Feb-11
Boot Procedure, Processor Mode
If STOP_TRANMISSION (CMD12) is successful, then the device is again ready for ATA com-
mands. However, if the error recovery procedure does not work as expected or there is another
timeout, the next step is to issue GO_IDLE_STATE (CMD0) to the device. GO_IDLE_STATE
(CMD0) is a hard reset to the device and completely resets all device states.
Note that after issuing GO_IDLE_STATE (CMD0), all device initialization needs to be completed
again. If the CE-ATA device completes all MMC commands correctly but fails the ATA command
with the ERR bit set in the ATA Status register, no error recovery action is required. The ATA
command itself failed implying that the device could not complete the action requested, how-
ever, there was no communication or protocol failure. After the device signals an error by setting
the ERR bit to one in the ATA Status register, the host may attempt to retry the command.
In boot operation mode, the processor can read boot data from the slave (MMC device) by keep-
ing the CMD line low after power-on before issuing CMD1. The data can be read from either the
boot area or user area, depending on register setting. As it is not possible to boot directly on SD-
CARD, a preliminary boot code must be stored in internal Flash.
• Issue STOP_TRANSMISSION (CMD12) and successfully receive the R1 response.
• Issue a software reset to the CE-ATA device using FAST_IO (CMD39).
1. Configure the HSMCI data bus width programming SDCBUS Field in the
2. Set the byte count to 512 bytes and the block count to the desired number of blocks,
3. Issue the Boot Operation Request command by writing to the HSMCI_CMDR register
4. The BOOT_ACK field located in the HSMCI_CMDR register must be set to one, if the
5. Host processor can copy boot data sequentially as soon as the RXRDY flag is
6. When Data transfer is completed, host processor shall terminate the boot stream by
HSMCI_SDCR register. The BOOT_BUS_WIDTH field located in the device Extended
CSD register must be set accordingly.
writing BLKLEN and BCNT fields of the HSMCI_BLKR Register.
with SPCMD field set to BOOTREQ, TRDIR set to READ and TRCMD set to “start data
transfer”.
BOOT_ACK field of the MMC device located in the Extended CSD register is set to one.
asserted.
writing the HSMCI_CMDR register with SPCMD field set to BOOTEND.
SAM3S Preliminary
811