ATSAM3S1BA-AU Atmel, ATSAM3S1BA-AU Datasheet - Page 364

• Manufacturer Part Number: ATSAM3S1BA-AU
• Description: IC MCU 32BIT 64KB FLASH 64LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S1BA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 47
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 10x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 47
• Ram Memory Size: 16KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

23.6
23.6.1
Figure 23-2.
23.6.1.1
Figure 23-3. NAND Flash Signal Multiplexing on SMC Pins
364
Connection to External Devices
SAM3S Preliminary
Data Bus Width
NAND Flash Support
Memory Connection for an 8-bit Data Bus
* in CCFG_SMCNFCS Matrix register
NCSx (activated if SMC_NFCSx=1) *
The data bus width is 8 bits.
Figure 23-2
The SMC integrates circuitry that interfaces to NAND Flash devices.
The NAND Flash logic is driven by the Static Memory Controller. It depends on the programming
of the SMC_NFCSx field in the CCFG_SMCNFCS Register on the Bus Matrix User Interface.
For details on this register, refer to the Bus Matrix User Interface section. Access to an external
NAND Flash device via the address space reserved to the chip select programmed.
The user can connect up to 4 NAND Flash devices with separated chip select.
The NAND Flash logic drives the read and write command signals of the SMC on the NANDOE
and NANDWE signals when the NCSx programmed is active. NANDOE and NANDWE are dis-
abled as soon as the transfer address fails to lie in the NCSx programmed address space.
Note: When NAND Flash logic is activated, (SMCNFCSx=1), NWE pin cannot be used i PIO
Mode but only in peripheral mode (NWE function). If NWE function is not used for other external
memories (SRAM, LCD), it must be configured in one of the following modes.
SMC
SMC
shows how to connect a 512K x 8-bit memory on NCS2.
NWE
NRD
A[18:0]
NCS[2]
D[7:0]
NWE
NRD
NAND Flash Logic
Write Enable
Output Enable
Memory Enable
D[7:0]
A[18:0]
NANDOE
NANDWE
NANDOE
NANDWE
6500C–ATARM–8-Feb-11