ATSAM3S1BA-AU Atmel, ATSAM3S1BA-AU Datasheet - Page 662

• Manufacturer Part Number: ATSAM3S1BA-AU
• Description: IC MCU 32BIT 64KB FLASH 64LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S1BA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 47
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 10x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 47
• Ram Memory Size: 16KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Figure 32-8. Receiver Framing Error
32.5.3
32.5.3.1
32.5.3.2
32.5.3.3
662
662
FRAME
RXRDY
SAM3S Preliminary
SAM3S Preliminary
URXD
Transmitter
Transmitter Reset, Enable and Disable
Transmit Format
Transmitter Control
S
D0
After device reset, the UART transmitter is disabled and it must be enabled before being used.
The transmitter is enabled by writing the control register UART_CR with the bit TXEN at 1. From
this command, the transmitter waits for a character to be written in the Transmit Holding Register
(UART_THR) before actually starting the transmission.
The programmer can disable the transmitter by writing UART_CR with the bit TXDIS at 1. If the
transmitter is not operating, it is immediately stopped. However, if a character is being pro-
cessed into the Shift Register and/or a character has been written in the Transmit Holding
Register, the characters are completed before the transmitter is actually stopped.
The programmer can also put the transmitter in its reset state by writing the UART_CR with the
bit RSTTX at 1. This immediately stops the transmitter, whether or not it is processing
characters.
The UART transmitter drives the pin UTXD at the baud rate clock speed. The line is driven
depending on the format defined in the Mode Register and the data stored in the Shift Register.
One start bit at level 0, then the 8 data bits, from the lowest to the highest bit, one optional parity
bit and one stop bit at 1 are consecutively shifted out as shown in the following figure. The field
PARE in the mode register UART_MR defines whether or not a parity bit is shifted out. When a
parity bit is enabled, it can be selected between an odd parity, an even parity, or a fixed space or
mark bit.
Figure 32-9. Character Transmission
When the transmitter is enabled, the bit TXRDY (Transmitter Ready) is set in the status register
UART_SR. The transmission starts when the programmer writes in the Transmit Holding Regis-
ter (UART_THR), and after the written character is transferred from UART_THR to the Shift
D1
Baud Rate
Example: Parity enabled
D2
UTXD
Clock
D3
D4
Start
Bit
D5
D6
D0
D7
D1
P
Detected at 0
Stop Bit
D2
stop
D3
D4
RSTSTA
D5
D6
D7
6500C–ATARM–8-Feb-11
6500C–ATARM–8-Feb-11
Parity
Bit
Stop
Bit