ATSAM3S1BA-AU Atmel, ATSAM3S1BA-AU Datasheet - Page 708

• Manufacturer Part Number: ATSAM3S1BA-AU
• Description: IC MCU 32BIT 64KB FLASH 64LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S1BA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 47
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 10x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 47
• Ram Memory Size: 16KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

33.7.7
708
708
SAM3S Preliminary
SAM3S Preliminary
Modem Mode
The USART features modem mode, which enables control of the signals: DTR (Data Terminal
Ready), DSR (Data Set Ready), RTS (Request to Send), CTS (Clear to Send), DCD (Data Car-
rier Detect) and RI (Ring Indicator). While operating in modem mode, the USART behaves as a
DTE (Data Terminal Equipment) as it drives DTR and RTS and can detect level change on DSR,
DCD, CTS and RI.
Setting the USART in modem mode is performed by writing the USART_MODE field in the Mode
Register (US_MR) to the value 0x3. While operating in modem mode the USART behaves as
though in asynchronous mode and all the parameter configurations are available.
Table 33-14
Table 33-14. Circuit References
The control of the DTR output pin is performed by writing the Control Register (US_CR) with the
DTRDIS and DTREN bits respectively to 1. The disable command forces the corresponding pin
to its inactive level, i.e. high. The enable command forces the corresponding pin to its active
level, i.e. low. RTS output pin is automatically controlled in this mode
The level changes are detected on the RI, DSR, DCD and CTS pins. If an input change is
detected, the RIIC, DSRIC, DCDIC and CTSIC bits in the Channel Status Register (US_CSR)
are set respectively and can trigger an interrupt. The status is automatically cleared when
US_CSR is read. Furthermore, the CTS automatically disables the transmitter when it is
detected at its inactive state. If a character is being transmitted when the CTS rises, the charac-
ter transmission is completed before the transmitter is actually disabled.
USART Pin
TXD
RTS
DTR
RXD
CTS
DSR
DCD
RI
gives the correspondence of the USART signals with modem connection standards.
V24
2
4
20
3
5
6
8
22
CCITT
103
105
108.2
104
106
107
109
125
Direction
From terminal to modem
From terminal to modem
From terminal to modem
From modem to terminal
From terminal to modem
From terminal to modem
From terminal to modem
From terminal to modem
6500C–ATARM–8-Feb-11
6500C–ATARM–8-Feb-11