ATSAM3S1BA-AU Atmel, ATSAM3S1BA-AU Datasheet - Page 423

• Manufacturer Part Number: ATSAM3S1BA-AU
• Description: IC MCU 32BIT 64KB FLASH 64LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S1BA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 47
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 10x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 47
• Ram Memory Size: 16KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

25.4
25.4.1
25.4.2
6500C–ATARM–8-Feb-11
Slow Clock
Slow Clock RC Oscillator
Slow Clock Crystal Oscillator
The Supply Controller embeds a slow clock generator that is supplied with the VDDIO power-
supply. As soon as the VDDIO is supplied, both the crystal oscillator and the embedded RC
oscillator are powered up, but only the embedded RC oscillator is enabled. This allows the slow
clock to be valid in a short time (about 100 µs).
The Slow Clock is generated either by the Slow Clock Crystal Oscillator or by the Slow Clock RC
Oscillator.
The selection between the RC or the crystal oscillator is made by writing the XTALSEL bit in the
Supply Controller Control Register (SUPC_CR).
By default, the Slow Clock RC Oscillator is enabled and selected. The user has to take into
account the possible drifts of the RC Oscillator. More details are given in the section “DC Char-
acteristics” of the product datasheet.
It can be disabled via the XTALSEL bit in the Supply Controller Control Register (SUPC_CR).
The Clock Generator integrates a 32,768 Hz low-power oscillator. In order to use this oscillator,
the XIN32/PA7 and XOUT32/P8 pins must be connected to a 32,768 Hz crystal. Two external
capacitors must be wired as shown in
Characteristics” of the product datasheet.
Note that the user is not obliged to use the Slow Clock Crystal and can use the RC oscillator
instead.
Figure 25-2. Typical Slow Clock Crystal Oscillator Connection
The user can select the crystal oscillator to be the source of the slow clock, as it provides a more
accurate frequency. The command is made by writing the Supply Controller Control Register
(SUPC_CR) with the XTALSEL bit at 1. This results in a sequence which first configures the PIO
lines multiplexed with XIN32 and XOUT32 to be driven by the oscillator, then enables the crystal
oscillator and then disables the RC oscillator to save power. The switch of the slow clock source
is glitch free. The OSCSEL bit of the Supply Controller Status Register (SUPC_SR) allows
knowing when the switch sequence is done.
Coming back on the RC oscillator is only possible by shutting down the VDDIO power supply. If
the user does not need the crystal oscillator, the XIN32 and XOUT32 pins can be left uncon-
nected since by default the XIN32 and XOUT32 system I/O pins are in PIO input mode after
reset.
The user can also set the crystal oscillator in bypass mode instead of connecting a crystal. In
this case, the user has to provide the external clock signal on XIN32. The input characteristics of
XIN32/PA7
32,768 Hz
Figure
Crystal
25-2. More details are given in the section “DC
XOUT32/PA8
SAM3S Preliminary
GND
423