ATSAM3S1BA-AU Atmel, ATSAM3S1BA-AU Datasheet - Page 427

• Manufacturer Part Number: ATSAM3S1BA-AU
• Description: IC MCU 32BIT 64KB FLASH 64LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S1BA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 47
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 10x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 47
• Ram Memory Size: 16KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

25.6
25.6.1
6500C–ATARM–8-Feb-11
Divider and PLL Block
Divider and Phase Lock Loop Programming
Then, at the 16th falling edge of Slow Clock, the MAINFRDY bit in the Clock Generator Main
Clock Frequency Register (CKGR_MCFR) is set and the counter stops counting. Its value can
be read in the MAINF field of CKGR_MCFR and gives the number of Main Clock cycles during
16 periods of Slow Clock, so that the frequency of the 4/8/12 MHz Fast RC oscillator or 3 to 20
MHz Crystal or Ceramic Resonator-based oscillator can be determined.
The device features two Divider/PLL Blocks that permit a wide range of frequencies to be
selected on either the master clock, the processor clock or the programmable clock outputs.
Additionally, they provide a 48 MHz signal to the embedded USB device and host ports regard-
less of the frequency of the main clock.
Figure 25-4
Figure 25-4. Dividers and PLL Blocks Diagram
The divider can be set between 1 and 255 in steps of 1. When a divider field (DIV) is set to 0, the
output of the corresponding divider and the PLL output is a continuous signal at level 0. On
reset, each DIV field is set to 0, thus the corresponding PLL input clock is set to 0.
The PLL (PLLA, PLLB) allows multiplication of the divider’s outputs. The PLL clock signal has a
frequency that depends on the respective source signal frequency and on the parameters DIV
(DIVA, DIVB) and MUL (MULA, MULB). The factor applied to the source signal frequency is
• when the Main Clock Oscillator selection is modified
MAINCK
shows the block diagram of the dividers and PLL blocks.
SLCK
Divider B
Divider A
DIVB
DIVA
MULB
MULA
PLLACOUNT
PLLBCOUNT
PLLADIV2
SAM3S Preliminary
PLLBDIV2
Counter
Counter
PLL B
PLL A
PLL B
PLL A
OUTB
OUTA
LOCKB
LOCKA
PLLBCK
PLLACK
427