EP2AGX45DF29I5N Altera, EP2AGX45DF29I5N Datasheet - Page 571

• Manufacturer Part Number: EP2AGX45DF29I5N
• Description: IC ARRIA II GX FPGA 45K 780FBGA
• Manufacturer: Altera
• Series: Arria II GXr

Specifications of EP2AGX45DF29I5N

• Number Of Logic Elements/cells: 42959
• Number Of Labs/clbs: 1805
• Total Ram Bits: 3435
• Number Of I /o: 364
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 780-FBGA
• Family Name: Arria® II GX
• Number Of Logic Blocks/elements: 45125
• # I/os (max): 364
• Frequency (max): 500MHz
• Operating Supply Voltage (typ): 900mV
• Logic Cells: 45125
• Ram Bits: 3565158.4
• Operating Supply Voltage (min): 0.87V
• Operating Supply Voltage (max): 0.93V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 780
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

Chapter 3: Configuring Multiple Protocols and Data Rates in Arria II Devices
Combining Transceiver Instances in Multiple Transceiver Blocks
Combining Transceiver Instances in Multiple Transceiver Blocks
December 2010 Altera Corporation
f
If you use the PLL cascade clock to provide input reference clocks to the CMU PLLs or
RX CDRs, there are requirements for combining transceiver channels (as described in
the following sections).
The Arria II GX and GZ transceiver can cascade the output of the general purpose
PLLs to the CMU PLLs and receiver CDRs. The left side of the Arria II GX and GZ
device contains a PLL cascade clock network—a single line network that connects the
PLL cascade clock to the transceiver block. Similarly, for Arria II GZ devices, the right
side PLLs can only be cascaded with the transceivers on the right side of the device.
Each side of the Arria II GZ device contains a PLL cascade clock network. This clock
line is segmented to allow different PLL cascade clocks to drive the transceiver CMU
PLLs and RX CDRs.
The segmentation locations differ based on the device family. Therefore, there are
restrictions when you want to combine transceiver channels that use different PLL
cascade clocks as input reference clocks.
For more information about using the PLL cascade clock and segmentation, refer to
the “PLL Cascading” section in the
“Creating Transceiver Channel Instances” on page 3–2
instantiate multiple transceiver channels using a single ALTGX instance. The
following section describes the method to instantiate multiple transceiver channels
using multiple transceiver blocks.
When you create a transceiver instance that has more than four transceiver channels,
the Quartus II software attempts to combine the transceiver channels in multiple
transceiver blocks, as shown in
Example 4
Consider that you create two ALTGX instances with the configuration shown in
Table
Table 3–8. Two ALTGX Instances for Example 4 for Arria II Devices
In this case, assuming that all the required parameters specified in
Channels Sharing a CMU PLL” on page 3–3
Quartus II software fits inst0 and inst1 in two transceiver blocks.
Instance Name
3–8.
inst0
inst1
Transceiver
Number of
Channels
7
1
Example
Receiver and Transmitter
Receiver and Transmitter
Transceiver Clocking in Arria II Devices
Configuration
4.
are identical in inst0 and inst1, the
Arria II Device Handbook Volume 2: Transceivers
describes the method to
Effective Data
Rate (Gbps)
3.125
3.125
“Multiple
Clock (Gbps)
chapter.
Reference
156.25
156.25
Input
3–13