EP4SE530H40I3 Altera, EP4SE530H40I3 Datasheet - Page 372

• Manufacturer Part Number: EP4SE530H40I3
• Description: IC STRATIX IV FPGA 530K 1517HBGA
• Manufacturer: Altera
• Series: STRATIX® IV Er

Specifications of EP4SE530H40I3

• Number Of Logic Elements/cells: 531200
• Number Of Labs/clbs: 21248
• Total Ram Bits: 27376
• Number Of I /o: 976
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 1517-HBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -

10–38
Figure 10–17. JTAG Configuration of Multiple Devices Using a Download Cable
Notes to
(1) Connect the pull-up resistor to the same supply voltage as the USB Blaster, MasterBlaster (V
(2) Connect the nCONFIG and MSEL[2..0] pins to support a non-JTAG configuration scheme. If you only use a JTAG configuration, connect
(3) Pin 6 of the header is a V
(4) You must connect nCE to GND or drive it low for successful JTAG configuration.
(5) The pull-up resistor value can vary from 1 k to 10 kΩ.
Stratix IV Device Handbook Volume 1
Pin 1
EthernetBlaster cable. Connect the voltage supply to V
nCONFIG to V
this value, refer to the
this pin is a no connect.
10-Pin Male Header
Download Cable
(JTAG Mode)
Figure
V
CCPD
10–17:
(1)
CCPGM
(1)
V
(3)
(5)
IO
1 kΩ
V
CCPD
V
CCPD
and MSEL[2..0] to GND. Pull DCLK either high or low, whichever is convenient on your board.
MasterBlaster Serial/USB Communications Cable User
Table 10–8. Dedicated Configuration Pin Connections During JTAG Configuration (Part 2 of 2)
When programming a JTAG device chain, one JTAG-compatible header is connected
to several devices. The number of devices in the JTAG chain is limited only by the
drive capability of the download cable. When four or more devices are connected in a
JTAG chain, Altera recommends buffering the TCK, TDI, and TMS pins with an on-board
buffer.
JTAG-chain device programming is ideal when the system contains multiple devices,
or when testing your system using JTAG BST circuitry.
Figure 10–17
(1)
(5)
nCONFIG
nSTATUS
CONF_DONE
DCLK
IO
V
CCPD
reference voltage for the MasterBlaster output driver. V
Signal
(1)
(2)
(2)
(2)
V
CCPGM
10 kΩ
TDI
nSTATUS
nCONFIG
DCLK
MSEL[2..0]
nCE
TRST
TMS
shows a multi-device JTAG configuration when using a download cable.
Stratix IV Device
(4)
Chapter 10: Configuration, Design Security, and Remote System Upgrades in Stratix IV Devices
Driven high by connecting to V
some control circuitry.
Pull to V
same JTAG chain, each nSTATUS pin must be pulled up to V
Pull to V
same JTAG chain, each CONF_DONE pin must be pulled up to V
CONF_DONE going high at the end of JTAG configuration indicates successful
configuration.
Do not leave DCLK floating. Drive low or high, whichever is more convenient on
your board.
CONF_DONE
TCK
CCPD
CCPGM
CCPGM
TDO
of the device.
V
CCPGM
V
using a 10-kΩ resistor. When configuring multiple devices in the
using a 10-kΩ resistor. When configuring multiple devices in the
CCPD
10 kΩ
(1)
(2)
(2)
(2)
V
CCPGM
10 kΩ
TDI
nSTATUS
nCONFIG
DCLK
MSEL[2..0]
nCE
TRST
TMS
Stratix IV Device
Guide. In the USB-Blaster, ByteBlaster II, and ByteBlasterMV cables,
(4)
CCPGM
CONF_DONE
IO
TCK
must match the device’s V
Description
, pulling up using a resistor, or driven high by
TDO
IO
V
CCPGM
V
pin), ByteBlaster II, ByteBlasterMV, or
CCPD
10 kΩ
(1)
(2)
(2)
(2)
V
CCPGM
10 kΩ
TDI
nSTATUS
nCONFIG
DCLK
MSEL[2..0]
nCE
TRST
Stratix II or Stratix II GX
TMS
CCPD
Stratix IV Device
(4)
April 2011 Altera Corporation
Device
. For more information about
CONF_DONE
CCPGM
TCK
CCPGM
TDO
individually.
JTAG Configuration
individually.
V
CCPGM
10 kΩ