DF61654N50FTV Renesas Electronics America, DF61654N50FTV Datasheet - Page 640

• Manufacturer Part Number: DF61654N50FTV
• Description: IC H8SX/1654 MCU FLASH 120TQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8SX/1600r

Specifications of DF61654N50FTV

• Core Processor: H8SX
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: I²C, IrDA, SCI, SmartCard, USB
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 75
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 120-TQFP, 120-VQFP
• For Use With: HS0005KCU11H - EMULATOR E10A-USB H8S(X),SH2(A)3DK1657 - DEV EVAL KIT FOR H8SX/1657
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Section 14 Serial Communication Interface (SCI, IrDA, CRC)
14.4.4
Before transmitting and receiving data, first clear the TE and RE bits in SCR to 0, then initialize
the SCI as described in a sample flowchart in figure 14.8 When the operating mode, transfer
format, etc., is changed, the TE and RE bits must be cleared to 0 before making the change. When
the TE bit is cleared to 0, the TDRE flag is set to 1. Note that clearing the RE bit to 0 does not
initialize the RDRF, PER, FER, and ORER flags, or RDR. When the external clock is used in
asynchronous mode, the clock must be supplied even during initialization.
Rev.1.00 Sep. 08, 2005 Page 590 of 966
REJ09B0219-0100
SCI Initialization (Asynchronous Mode)
Clear TE and RE bits in SCR to 0
SCR to 1, and set RIE, TIE, TEIE,
Set CKE1 and CKE0 bits in SCR
Set corresponding bit in ICR to 1
Set data transfer format in
<Initialization completion>
(TE and RE bits are 0)
1-bit interval elapsed
Set TE or RE bit in
Set value in BRR
Start initialization
SMR and SCMR
and MPIE bits
Figure 14.8 Sample SCI Initialization Flowchart
Yes
Wait
No
[1]
[2]
[3]
[4]
[5]
[1]
[2]
[3]
[4]
[5]
Set the bit in ICR for the corresponding
pin when receiving data or using an
external clock.
Set the clock selection in SCR.
Be sure to clear bits RIE, TIE, TEIE, and
MPIE, and bits TE and RE, to 0.
When the clock output is selected in
asynchronous mode, the clock is output
immediately after SCR settings are
made.
Set the data transfer format in SMR and
SCMR.
Write a value corresponding to the bit
rate to BRR. This step is not necessary
if an external clock is used.
Wait at least one bit interval, then set the
TE bit or RE bit in SCR to 1. Also set
the RIE, TIE, TEIE, and MPIE bits.
Setting the TE and RE bits enables the
TxD and RxD pins to be used.