NH82801GHM S L8YR Intel, NH82801GHM S L8YR Datasheet - Page 136
![no-image](/images/manufacturer_photos/0/3/336/intel_sml.jpg)
NH82801GHM S L8YR
Manufacturer Part Number
NH82801GHM S L8YR
Description
Manufacturer
Intel
Datasheet
1.NH82801GHM_S_L8YR.pdf
(848 pages)
Specifications of NH82801GHM S L8YR
Lead Free Status / RoHS Status
Compliant
- Current page: 136 of 848
- Download datasheet (7Mb)
5.9.2.2
5.9.2.3
5.9.2.4
5.9.3
5.9.4
5.9.4.1
136
ICW2
The second write in the sequence (ICW2) is programmed to provide bits [7:3] of the
interrupt vector that will be released during an interrupt acknowledge. A different base
is selected for each interrupt controller.
ICW3
The third write in the sequence (ICW3) has a different meaning for each controller.
ICW4
The final write in the sequence (ICW4) must be programmed for both controllers. At
the very least, bit 0 must be set to a 1 to indicate that the controllers are operating in
an Intel Architecture-based system.
Operation Command Words (OCW)
These command words reprogram the Interrupt controller to operate in various
interrupt modes.
Modes of Operation
Fully Nested Mode
In this mode, interrupt requests are ordered in priority from 0 through 7, with 0 being
the highest. When an interrupt is acknowledged, the highest priority request is
determined and its vector placed on the bus. Additionally, the ISR for the interrupt is
set. This ISR bit remains set until: the processor issues an EOI command immediately
before returning from the service routine; or if in AEOI mode, on the trailing edge of
the second INTA#. While the ISR bit is set, all further interrupts of the same or lower
priority are inhibited, while higher levels generate another interrupt. Interrupt priorities
can be changed in the rotating priority mode.
• For the master controller, ICW3 is used to indicate which IRQ input line is used to
• For the slave controller, ICW3 is the slave identification code used during an
• OCW1 masks and unmasks interrupt lines.
• OCW2 controls the rotation of interrupt priorities when in rotating priority mode,
• OCW3 is sets up ISR/IRR reads, enables/disables the special mask mode (SMM),
cascade the slave controller. Within the ICH7, IRQ2 is used. Therefore, bit 2 of
ICW3 on the master controller is set to a 1, and the other bits are set to 0s.
interrupt acknowledge cycle. On interrupt acknowledge cycles, the master
controller broadcasts a code to the slave controller if the cascaded interrupt won
arbitration on the master controller. The slave controller compares this
identification code to the value stored in its ICW3, and if it matches, the slave
controller assumes responsibility for broadcasting the interrupt vector.
and controls the EOI function.
and enables/disables polled interrupt mode.
Intel
®
ICH7 Family Datasheet
Functional Description
Related parts for NH82801GHM S L8YR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![NH82801GHM](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
82801GHM I/O Controller Hub 7 (ICH7MDH)
Manufacturer:
Intel Corporation
Datasheet:
![RJ80535VC600512](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Microprocessor: Intel Celeron M Processor 320 and Ultra Low Voltage Intel Celeron M Processor at 600MHz
Manufacturer:
Intel Corporation
![82550GY](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 82550 Fast Ethernet Multifunction PCI/CardBus Controller
Manufacturer:
Intel Corporation
Datasheet:
![DA28F320J5-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 120 ns
Manufacturer:
Intel Corporation
Datasheet:
![G28F640J5-150](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 64 Mbit. Access speed 150 ns
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5-100](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel StrataFlash memory 32 Mbit. Access speed 100 ns
Manufacturer:
Intel Corporation
Datasheet:
![DA28F640J5A-150](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
DA28F640J5A-1505 Volt Intel StrataFlash Memory
Manufacturer:
Intel Corporation
Datasheet:
![DA28F320J5A-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
Datasheet:
![E28F320J5A-120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
5 Volt Intel StrataFlash?? Memory
Manufacturer:
Intel Corporation
![NHE6300ESB](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 6300ESB I/O Controller Hub
Manufacturer:
Intel Corporation
Datasheet:
![NH82801DB](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 82801DB I/O Controller Hub (ICH4), Pb-Free SLI
Manufacturer:
Intel Corporation
Datasheet:
![FW82801FB](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel 82801FB I/O Controller Hub (ICH6)
Manufacturer:
Intel Corporation
Datasheet:
![28F640J3A120](/images/manufacturer_photos/0/3/337/intel_corporation_tmb.jpg)
Part Number:
Description:
Intel Strataflash Memory28F128J3 28F640J3 28F320J3
Manufacturer:
Intel Corporation
Datasheet: