pc87591l National Semiconductor Corporation, pc87591l Datasheet - Page 115
![no-image](/images/no-image-200.jpg)
pc87591l
Manufacturer Part Number
pc87591l
Description
Lpc Mobile Embedded Controllers
Manufacturer
National Semiconductor Corporation
Datasheet
1.PC87591L.pdf
(437 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PC87591L
Manufacturer:
NS
Quantity:
5 510
Company:
Part Number:
PC87591L
Manufacturer:
MOT
Quantity:
5 510
Company:
Part Number:
pc87591l-VPCN01
Manufacturer:
NSC
Quantity:
5 510
Part Number:
pc87591l-VPCN01
Manufacturer:
NS/国半
Quantity:
20 000
- Current page: 115 of 437
- Download datasheet (3Mb)
Revision 1.07
Embedded Controller Modules
Output Buffer
The output buffer is a TRI-STATE buffer. The output type (i.e., CMOS or TTL) and its driving capabilities are described in
Section 2.2 on page 41.
Input Buffer
The I/O port input buffer characteristics are defined in Section 2.2 on page 41.
The input buffer has an enable input. When enabled, the buffer inputs the pin’s logic level to the on-chip modules. When
disabled, the input is blocked to prevent supply leakage currents.
Weak Pull-Up
The weak pull-up is enabled when the corresponding bit of PxWPU is set (1) and the pin is configured as an input port. When
the pin is configured for input, this pull-up can prevent the input from being in an undefined state. When the pin is configured
as an output port, this pull-up is disabled.
Alternate Function
The PxALT controls the use of each of the port pins for GPIO or for the pin’s respective alternate function.
When PxALT bit is cleared (0):
When a bit in PxALT is set (1):
Port Direction
The Port Direction register (PxDIR) controls the direction of the port. If set (1), each bit in the register causes the correspond-
ing port signal to serve as an output port, thus enabling the output buffer.
When cleared, the port serves as an input port signal, thus putting the output buffer in TRI-STATE.
If the corresponding bit in PxWPU is set, it also enables the pull-up.
Data Output
The Data Output (PxDOUT) register holds the data to be driven onto the pin, when the respective pin is configured as GPIO
and its direction is set as output.
Data Input
The Data Input (PxDIN) register returns the current value/state of the pin. This register can always be read.
Open Drain
To use the GPIO pin as an inverting open-drain output buffer, the software should clear the corresponding bit in PxDOUT
register and then use PxDIR register to set the value to the port pin.
When the signal direction is set as output (1), a value of 0 is forced. When the direction is set for input (0), the signal is in
TRI-STATE and is not forced low.
The internal weak pull-up can pull the signal high when it is not forced low, by writing (1) to the corresponding bit of PxWPU.
Input Echo Function
Some of the Px pins can echo the value of an input pin. Figure 34 illustrates the modified structure of Px port pins that support
the echo function. The input echo function may be used when the Px pin is configured to operate as a General-Purpose
output pin.
Table 9 on page 60 defines pairs of input ports (Pi) and output ports (Po) and the Echo Enable bit associated with each pair.
When the pair’s Echo Enable bit is set, and if Po is configured as output, the value from the input bit (Pi) is output to the
respective output port (Po). When the pair’s Echo Enable bit is cleared, and if Po is configured as output, the value in
PxDOUT is output to the respective output port.
The corresponding pin is used as a GPIO pin.
The output buffer is controlled by the Direction and Data Output registers.
The input buffer is routed to the Data Input register.
In this case, the input buffer is blocked, except when the buffer is actually being read.
The pull-up is enabled when both the PxWPU is set and the device puts the output buffer in TRI-STATE.
The corresponding pin is used for an alternate function (i.e., a signal from/to some other PC87591x module).
The output buffer data and TRI-STATE are controlled by signals from the alternate module.
The input buffer is always enabled when the alternate function is an input; therefore, to minimize current consump-
tion, the signal should be held above V
The pull-up is enabled when PxWPU is set and the device puts the output buffer in TRI-STATE.
CC
(Continued)
0.2 or below GND+0.2V.
115
www.national.com
Related parts for pc87591l
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![mma1270keg](/images/no-image3.png)
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
![ADC12034](/images/no-image3.png)
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2350](/images/no-image3.png)
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2324](/images/no-image3.png)
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LMX2301](/images/no-image3.png)
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![NDS8963](/images/no-image3.png)
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM1201](/images/no-image3.png)
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM3501TL-16](/images/no-image3.png)
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
![AD9621](/images/no-image3.png)
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM2403](/images/no-image3.png)
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
![LM592M](/images/no-image3.png)
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
![ADC10061](/images/no-image3.png)
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS36277TMX](/images/no-image3.png)
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS3654](/images/no-image3.png)
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
![DS3662](/images/no-image3.png)
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: