XW2Z-200J-B9 Omron, XW2Z-200J-B9 Datasheet - Page 463

• Manufacturer Part Number: XW2Z-200J-B9
• Description: CONNECTOR CABLE 2M
• Manufacturer: Omron

Specifications of XW2Z-200J-B9

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XW2Z200JB9

436
Auxiliary Area Allocations
A812
A813
A814
A815
A820
A821
Word
00
04
08
12
14
00
04
08
12
14
00
00
00
02
03
07
12
13
14
15
00
15
Bits
Analog Output 1 Flags
Analog Output 1 Flags
Analog Output 1 Conversion Enable Bit
Analog Output 2 Conversion Enable Bit
Adjustment Mode Com-
mand Bits
(Effective only when A825
is 5A5A hex.)
Adjustment Mode Status
Name
User Adjust-
ment Com-
pleted
Operating
Output SV Error ON: ON when the output SV setting is outside of the allowed setting
Factory Adjust-
ment Value
Error
User Adjust-
ment Value
Error
User Adjust-
ment Com-
pleted
Operating
Output SV Error
Factory Adjust-
ment Value
Error
User Adjust-
ment Value
Error
Adjustment
Enable
Adjustment
Mode Specifier
Adjustment
Value Increment
Adjustment
Value Decre-
ment
Adjustment
Value Clear
Adjustment
Value Set
Adjustment
Operation Error
Adjustment
Mode Started
Initial value is 0.
Set to 1 if user performs offset/gain adjustment and Returns to fac-
tory default setting of 0 if adjustment value is cleared.
ON: ON while the analog output is being changed by ACC(888).
OFF: Turned OFF when target value is reached.
range.
OFF: OFF when the output SV is within range.
ON: ON when the factory-set data stored in flash memory is invalid.
OFF: OFF when the factory-set data stored in flash memory is nor-
mal.
ON: ON when the user-set adjustment value stored in flash memory
is invalid.
OFF: OFF when the user-set adjustment value stored in flash mem-
ory is normal.
Same as for Analog Output 1 Flags.
ON: Enables D/A conversion (enables analog output).
OFF: Disables D/A conversion (analog values output according to
Output Stop Function specification in System Setup).
Note This bit is cleared when the Modules operating mode is
changed between RUN or MONITOR mode and PROGRAM mode.
ON: Enables D/A conversion (enables analog output).
OFF: Disables D/A conversion (analog values output according to
Output Stop Function specification in System Setup).
Note This bit is cleared when the Modules operating mode is
changed between RUN or MONITOR mode and PROGRAM mode.
Analog Input
Analog Output 1
Analog Output 2
OFF: Offset adjustment
ON: Gain adjustment
While this bit is ON, the offset or gain value will be incremented by
one resolution unit each 0.5 ms.
While this bit is ON, the offset or gain value will be decremented by
one resolution unit each 0.5 ms.
OFF to ON: Clears the adjustment data to the factory defaults.
OFF to ON: Reads the present value in the Adjustment Mode Moni-
tor Area (A822 and A823) and saves this value to flash memory. This
adjustment value will be used for the next normal mode operation.
ON when an operational error has been made, such as turning ON
both the Analog Input and Analog Output 2 Adjustment Enable Bits
at the same time.
ON during adjustment mode operation (when A825 contains 5A5A
hex).
OFF: Adjustment disabled.
ON: Adjustment enabled.
When one of these bits is turned ON, the
default value (offset or gain value) corre-
sponding to the selected I/O signal range is
transferred to Adjustment Mode Monitor Area
(A822 and A823).
Function
Appendix D