XW2Z-200J-B9 Omron, XW2Z-200J-B9 Datasheet - Page 442

• Manufacturer Part Number: XW2Z-200J-B9
• Description: CONNECTOR CABLE 2M
• Manufacturer: Omron

Specifications of XW2Z-200J-B9

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XW2Z200JB9

System Setup, Auxiliary Area Allocations, and Built-in I/O Allocations
A814
A815
A820
A821
A822
A823
A824
A825
Address
00
01 to 15 Reserved
00
01 to 15 Reserved
00
01
02
03
04 to 06
07
08 to 11
12
13
14
15
00
01 to 14
15
00 to 15 Adjustment Mode
00 to 15
00 to 15
00 to 15 Adjustment Mode Password
Bits
Analog Output 1
Analog Output 2
Adjustment Mode
Command Bits
(Effective only
when A825 is
5A5A hex.)
Adjustment Mode
Status
Monitor
(Effective only
when A825 is
5A5A hex.)
Name
Conversion Enable
Bit
Conversion Enable
Bit
Adjustment Enable Analog Input
Reserved
Adjustment Mode
Specifier
Reserved
Adjustment Value
Increment
Adjustment Value
Decrement
Adjustment Value
Clear
Adjustment Value
Set
Adjustment Opera-
tion Error
Reserved
Adjustment Mode
Started
Both Analog Input
and Analog Out-
puts
Analog Inputs
ON: Enables D/A conversion (enables analog output).
OFF: Disables DA conversion (analog values output
according to Output Stop Function specification in Sys-
tem Setup).
Note This bit is cleared when the Modules operating
---
ON: Enables D/A conversion (enables analog output).
OFF: Disables DA conversion (analog values output
according to Output Stop Function specification in Sys-
tem Setup).
Note This bit is cleared when the Modules operating
---
Reserved
Analog Out-
put 1
Analog Out-
put 2
OFF: Offset adjustment
ON: Gain adjustment
While this bit is ON, the offset or gain value will be
incremented by one resolution unit each 0.5 ms.
While this bit is ON, the offset or gain value will be dec-
remented by one resolution unit each 0.5 ms.
OFF to ON: Clears the adjustment data to the factory
defaults.
OFF to ON: Reads the present value in the Adjustment
Mode Monitor Area (A822 and A823) and saves this
value to flash memory. This adjustment value will be
used for the next normal mode operation.
ON when an operational error has been made, such as
turning ON both the Analog Input and Analog Output 2
Adjustment Enable Bits at the same time.
ON during adjustment mode operation (when A825
contains 5A5A hex).
Gain Value
Monitor
Number of
Average
Value Sam-
ples in Adjust-
ment Mode
5A5A hex: Adjustment mode enabled.
Other value: Adjustment mode disabled.
Setting Off-
set Monitor
mode is changed between RUN or MONITOR
mode and PROGRAM mode.
mode is changed between RUN or MONITOR
mode and PROGRAM mode.
OFF: Adjustment disabled.
ON: Adjustment enabled.
When one of these bits is turned ON,
the default value (offset or gain value)
corresponding to the selected I/O signal
range is transferred to Adjustment
Mode Monitor Area (A822 and A823).
The values in
these words
can be over-
written
directly, with-
out using the
Adjustment
Value Incre-
ment/Decre-
ment Bits.
Indicates the number of values to be
averaged to obtain the Offset/Gain
Value Monitor values in adjustment
mode. The number of samples can be
set between 0000 and 0040 hex (0 to
64). Set this parameter before turning
ON the Adjustment Enable Bit.
Function
• 10 to 10 V: FE0C to
• 0 to 10 V, 0 to 5 V, 1 to
• 10 to 10 V: 1194 to
• 0 to 10 V, 0 to 5 V, 1 to
01F4 hex
5 V: FF38 to 00C8 hex
157C hex
5 V: 0ED8 to 1068 hex
Appendix C
User
---
User
---
User
Module
Module/User
User
User
Controlled by
415