XW2Z-200J-B9 Omron, XW2Z-200J-B9 Datasheet - Page 460

• Manufacturer Part Number: XW2Z-200J-B9
• Description: CONNECTOR CABLE 2M
• Manufacturer: Omron

Specifications of XW2Z-200J-B9

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XW2Z200JB9

Auxiliary Area Allocations
A461 to
A473
A500
A501
A502 to
A507
A508
A526
A527
A528
A532
Word
00 to 15 EM Banks 0 to C, Area ID Codes
14
00 to 15 CPU Bus Unit Restart Bits
00 to 15 Special I/O Unit Restart Bits
09
11
12
13
14
15
00
01
07
00 to 07 Online Editing Disable Bit Validator
09
02
03
04
05
10
11
12
13
00 to 15 Interrupt Counter 0 Counter SV
Bits
Error Log Pointer Reset and Memory Not
Held Flag OFF Bit
Differentiate Monitor Completed Flag
Trace Trigger Monitor Flag
Trace Completed Flag
Trace Busy Flag
Trace Start Bit
Sampling Start Bit
RS-232C Port Restart Bit
Peripheral Port Restart Bit
RS-422A Port Restart Bit
Online Editing Disable Bit
RS-232C
Port
Error
Flags
Periph-
eral Port
Error
Flags
Parity Error Flag
Framing Error Flag
Overrun Error Flag
Timeout Error Flag
Parity Error Flag
Framing Error Flag
Overrun Error Flag
Timeout Error Flag
Name
0050 to 005C (fixed)
The error log pointer in A300 is reset to 0000 hex and Memory Not
Held Flag (A404.14) is turned OFF when this bit is turned ON.
Turn these bits ON to restart (initialize) the CPU Bus Unit with the
corresponding unit number. Bits 00 to 15 correspond to unit numbers
0 to F.
Turn these bits ON to restart (initialize) the Special I/O Unit with the
corresponding unit number. Bits A502.10 to A507.15 correspond to
unit numbers 10 to 95.
Turns ON when the differentiate monitor condition has been estab-
lished during execution of differentiation monitoring.
(This flag will be turned OFF when differentiation monitoring starts.)
Turns ON when a trigger condition is established by the Trace Start
Bit (A508.14). OFF when the next Data Trace is started by the Sam-
pling Start bit (A508.15).
Turns ON when sampling of a region of trace memory has been com-
pleted during execution of a Trace.
Turns OFF when the next time the Sampling Start Bit (A508.15) is
turned from OFF to ON.
Turns ON when the Sampling Start Bit (A508.15) is turned from OFF
to ON. Turns OFF when the trace is completed.
Turn this bit ON to establish the trigger condition. The offset indi-
cated by the delay value (positive or negative) determines which data
samples are valid.
When a data trace is started by turning this bit from OFF to ON from
the CX-Programmer, the FQM1 will begin storing data in Trace Mem-
ory by one of the three following methods:
1) Data is sampled at regular intervals (10 to 2,550 ms).
2) Data is sampled when TRSM(045) is executed in the program.
3) Data is sampled at the end of every cycle.
The operation of A508.15 can be controlled only from the CX-Pro-
grammer.
Turn this bit ON to restart the RS-232C port.
This bit is turned OFF automatically when the restart processing is
completed.
Turn this bit ON to restart the peripheral port.
This bit is turned OFF automatically when the restart processing is
completed.
Turn this bit ON to restart the RS-422A port.
This bit is turned OFF automatically when the restart processing is
completed.
The Online Editing Disable Bit (A52709) is valid only when this byte
contains 5A.
5A: Online Editing Disable Bit enabled
Other value: Online Editing Disable Bit disabled
Turn this bit ON to disable online editing.
These error flags turn ON when an error has occurred at the RS-
232C port.
These error flags turn ON when an error has occurred at the periph-
eral port.
Used for interrupt input 0 in counter mode.
Sets the count value at which the interrupt task will start. Interrupt
task 000 will start when interrupt counter 0 has counted this number
of pulses.
Setting range: 0000 to FFFF
Note This area is valid only in Motion Control Modules.
Function
Appendix D
433