XW2Z-200J-B9 Omron, XW2Z-200J-B9 Datasheet - Page 452

• Manufacturer Part Number: XW2Z-200J-B9
• Description: CONNECTOR CABLE 2M
• Manufacturer: Omron

Specifications of XW2Z-200J-B9

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: XW2Z200JB9

Other Error Flags and Bits
Error Log and Error Code
FAL/FALS Errors
Memory Errors
System Setup
Other
System Setup, Auxiliary Area Allocations, and Built-in I/O Allocations
A100 to
A199
A300
A500
A400
A401
A402
A401
A403
A316
A402
A406
A401
A316
A555
Address
Address
Address
Address
Address
00 to 15 Error Log Area
00 to 15 Error Log Pointer
14
00 to 15 Error code
06
15
14
15
00
04
07
10
14
14
10
00 to 15 System Setup Error
08
05
15
Bits
Bits
Bits
Bits
Bits
Error Log Pointer Reset
and Memory Not Held
Flag OFF Bit
FALS Error Flag
(fatal error)
FAL Error Flag
(non-fatal error)
I/O Bus Error Flag
Memory Error Flag (fatal
error)
UM Error Flag
System Setup Error
Flag
Routing Table Error Flag Turns ON when there is an error in the routing table.
Flash Memory Error
Flag
Flash Memory DM
Checksum Error Flag
Memory Not Held Flag
System Setup Error
Flag
Location
Cycle Time Too Long
Flag (fatal error)
Constant Cycle Time
Exceeded Flag
Constant Cycle Time
Exceeded Error Clear
Bit
Name
Name
Name
Name
Name
When an error has occurred, the error code and error contents are
stored in the Error Log Area.
When an error occurs, the Error Log Pointer (binary) is incremented by
1 to indicate the location where the next error will be recorded as an
offset from the beginning of the Error Log Area (A100 to A199).
When this bit goes from OFF to ON, the error log pointer in A408 is
reset to 0000 hex and Memory Not Held Flag (A404.14) is turned OFF.
When a non-fatal error (user-defined FAL(006) or system error) or a
fatal error (user-defined FALS(007) or system error) occurs, the hexa-
decimal error code is written to this word.
Turns ON when a non-fatal error is generated by the FALS(006)
instruction. The FQM1 will stop operating.
Turns ON when a non-fatal error is generated by executing FAL(006).
The FQM1 will continue operating.
ON when an error occurs in a data transfer between the Coordinator
Module and a Motion Control Module.
The Module will stop operating.
Turns ON when there is an error in the memory. FQM1 operation will
stop and the ERR indicators on the front of the Modules will light.
Turns ON when there is an error in the user memory.
Turns ON when there is an error in the System Setup in the Coordina-
tor Module or Motion Control Module.
Turns ON when the flash memory is physically destroyed.
Turns ON when there is an error in the DM Area data backed up in
flash memory.
Turns ON when corruption is found in the check performed after turn-
ing ON power in the areas backed up during power interruptions (DM
Area (Motion Control Module only) and Error Log Area).
Turns ON when there is a setting error in the System Setup.
When there is a setting error in the System Setup, the location (setting
address) of that error is written to A406 in 4-digit hexadecimal.
Turns ON if the cycle time exceeds the maximum cycle time set in the
System Setup (the Watch Cycle Time).
Turns ON when the actual cycle time exceeds the specified constant
(minimum) cycle time.
Used to enable the constant cycle time function again after the con-
stant cycle time has been exceeded.
Function
Function
Function
Function
Function
Appendix C
Module
User
Module
Module
Module
Module
Module
User
Controlled by
Controlled by
Controlled by
Controlled by
Controlled by
425