TMP91xy25FG Toshiba, TMP91xy25FG Datasheet - Page 192

no-image

TMP91xy25FG

Manufacturer Part Number
TMP91xy25FG
Description
Manufacturer
Toshiba
Datasheet

Specifications of TMP91xy25FG

Package
LQFP100
Rom Types(m=mask,p=otp, F=flash,e=eeprom)
Romless
Rom Combinations
Romless
Ram Combinations
Ramless
Architecture
16-bit CISC
Usb/spi Channels
-
Uart/sio Channels
2
I2c/sio Bus Channels
-
(s)dram Controller
-
Adc 10-bit Channel
4
Da Converter
-
Timer 8-bit Channel
4
Timer 16-bit Channel
-
Pwm 8-bit Channels
-
Pwm 16-bit Channels
-
Cs/wait Controller
4
Dual Clock
Y
Number Of I/o Ports
49
Power Supply Voltage(v)
3.0 to 3.6
3.13.6
Explanation of the interrupt signal and alarm signal
(1) When the alarm register and the timer clock correspond, output “0”.
(2) 1Hz Output clock of 1Hz.
(3) 16Hz Output clock of 16Hz.
(1) In accordance with alarm register and a clock, output “0”.
following three signals from
PAGER<PAGE>. INTRTC outputs a 1-shot pulse when the falling edge is detected.
RTC is not initializes initialized by RESET. Therefore, when the clock or alarm
function is used, clear interrupt request flag in INTC (interrupt controller).
of PAGER<ENAALM>= “1”, output “0” to
of all alarm becomes don’t care. In this case, always accorded with value of a clock and
request INTRTC interrupt if PAGER<ENAALM> is “1”.
writing in data at each register of PAGE1.
PAGER<INTENA><ENAALM> is “1”. However, contents (don't care state) which does
not set it up is considered to always accord.
independence. Initialization of alarm and resetting of alarm register set to “Don’t care”.
(PM12:00) every day.
clock at 32 kHz (about 30μs) for the time register setting to become valid. In the above
example, it is necessary to set 31μs of set up time between setting the time register and
enabling the alarm register.
Note: This set up time is unnecessary when you use only internal interruption.
The alarm function used by setting the PAGE1 register and outputting either of the
When value of a clock of PAGE0 accorded with alarm register of PAGE1 with a state
Follows are ways using alarm.
Initialization of alarm is done by writing in “1” at RESTR<RSTALM>, setting value
Setting alarm min., alarm hour, alarm day and alarm the day week are done by
When all setting contents accorded, RTC generates INTRTC interrupt, if
The contents, which set it up once, cannot be returned to don't care state in
The following is an example program for outputting alarm from
When CPU is operated by high frequency oscillation, it may take a maximum of one
( LD
LD
LD
LD
LD
LD
LD
LD
(PAGER), 09H
(RESTR), D0H
(DAYR), 01H
(DATAR),01H
(HOURR), 12H
(MINR), 00H
(PAGER), 0CH
(PAGER), 8CH
91C025-191
ALARM
;
;
;
;
;
;
;
;
Alarm disable, setting PAGE1
Alarm initialize
W0
1 day
Setting 12 o’clock
Setting 00 min
Set up time 31 μs (Note)
Alarm enable
Interrupt enable )
pin as follows by write writing “1” to
ALARM
pin and occur INTRTC.
ALARM
TMP91C025
2007-02-28
-pin at noon

Related parts for TMP91xy25FG