D6417729RHF200BV Renesas Electronics America, D6417729RHF200BV Datasheet - Page 437

• Manufacturer Part Number: D6417729RHF200BV
• Description: IC SUPER H MPU ROMLESS 208QFP
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7700r

Specifications of D6417729RHF200BV

• Core Processor: SH-3 DSP
• Core Size: 32-Bit
• Speed: 200MHz
• Connectivity: EBI/EMI, FIFO, IrDA, SCI, SmartCard
• Peripherals: DMA, POR, WDT
• Number Of I /o: 96
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.85 V ~ 2.15 V
• Data Converters: A/D 8x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 208-QFP Exposed Pad, 208-eQFP, 208-HQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -

12.3.2
DMA transfer requests are basically generated in either the data transfer source or destination, but
they can also be generated by devices and on-chip peripheral modules that are neither the source
nor the destination. Transfers can be requested in three modes: auto-request, external request, and
on-chip module request. The request mode is selected in the RS3–RS0 bits of DMA channel
control registers 0–3 (CHCR0–CHCR3).
Auto-Request Mode: When there is no transfer request signal from an external source, as in a
memory-to-memory transfer or a transfer between memory and an on-chip peripheral module
unable to request a transfer, the auto-request mode allows the DMAC to automatically generate a
transfer request signal internally. When the DE bit of CHCR0–CHCR3 and the DME bit of
DMAOR are set to 1, the transfer begins so long as the TE bit of CHCR0–CHCR3 and the NMIF
bit of DMAOR are 0.
External Request Mode: In this mode a transfer is performed in response to the request signal
(DREQ) of an external device. Choose one of the modes shown in table 12.3 according to the
application system. When this mode is selected, if DMA transfer is enabled (DE = 1, DME = 1,
TE = 0, NMIF = 0), a transfer is performed upon a request at the DREQ input. Choose DREQ
detection by either a falling edge or low level of the signal input with the DS bit in CHCR0 and
CHCR1 (DS = 0 for level detection, DS = 1 for edge detection). The source of the transfer request
does not have to be the data transfer source or destination.
Table 12.3 Selecting External Request Modes with RS Bits
Note: * External memory, memory-mapped external device, on-chip memory, on-chip peripheral
On-Chip Module Request: In this mode a transfer is performed in response to a transfer request
signal (interrupt request signal) of an on-chip module. This mode cannot be set in case of 16-byte
transfer. These are six transfer request signals: the receive-data-full interrupts (RXI) and the
transmit-data-empty interrupts (TXI) from two serial communication interfaces (IrDA, SCIF), the
A/D conversion end interrupt (ADI) of the A/D converter, and the compare match timer interrupt
(CMI) of the CMT (table 12.4). When this mode is selected, if DMA transfer is enabled (DE = 1,
DME = 1, TE = 0, NMIF = 0), a transfer is performed upon input of a transfer request signal. The
RS3
0
module (excluding DMAC, UBC, and BSC)
RS2
0
DMA Transfer Requests
RS1
0
1
RS0
0
0
1
Dual address
mode
Single address
mode
Address Mode
Source
Any *
External memory,
memory-mapped
external device
External device with
DACK
Rev. 5.0, 09/03, page 389 of 806
Destination
Any *
External device with
DACK
External memory,
memory-mapped
external device