LPC1769FBD100,551 NXP Semiconductors, LPC1769FBD100,551 Datasheet - Page 206

• Manufacturer Part Number: LPC1769FBD100,551
• Description: IC ARM CORTEX MCU 512K 100-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC17xxr

Specifications of LPC1769FBD100,551

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 100-LQFP
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 120MHz
• Connectivity: CAN, Ethernet, I²C, IrDA, Microwire, SPI, SSI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 70
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 3.6 V
• Data Converters: A/D 8x12b, D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC17
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: Ethernet, USB, OTG, CAN
• Maximum Clock Frequency: 120 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, MCB1760, MCB1760U, MCB1760UME
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 8 Channel
• On-chip Dac: 10 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4966; 935290522551

NXP Semiconductors
UM10360
User manual
10.17.18 Reset
The Ethernet block has a hard reset input which is connected to the chip reset, as well as
several soft resets which can be activated by setting the appropriate bit(s) in registers. All
registers in the Ethernet block have a value of 0 after a hard reset, unless otherwise
specified.
Hard reset
After a hard reset, all registers will be set to their default value.
Soft reset
Parts of the Ethernet block can be soft reset by setting bits in the Command register and
the MAC1 configuration register.The MAC1 register has six different reset bits:
The above reset bits must be cleared by software.
The Command register has three different reset bits:
•
•
•
•
•
•
•
•
SOFT RESET: Setting this bit will put all modules in the MAC in reset, except for the
MAC registers (at addresses 0x000 to 0x0FC). The value of the soft reset after a
hardware reset assertion is 1, i.e. the soft reset needs to be cleared after a hardware
reset.
SIMULATION RESET: Resets the random number generator in the Transmit
Function. The value after a hardware reset assertion is 0.
RESET MCS/Rx: Setting this bit will reset the MAC Control Sublayer (pause frame
logic) and the receive function in the MAC. The value after a hardware reset assertion
is 0.
RESET Rx: Setting this bit will reset the receive function in the MAC. The value after a
hardware reset assertion is 0.
RESET MCS/Tx: Setting this bit will reset the MAC Control Sublayer (pause frame
logic) and the transmit function in the MAC. The value after a hardware reset
assertion is 0.
RESET Tx: Setting this bit will reset the transmit function of the MAC. The value after
a hardware reset assertion is 0.
TxReset: Writing a ‘1’ to the TxReset bit will reset the transmit data path, excluding the
MAC portions, including all (read-only) registers in the transmit data path, as well as
the TxProduceIndex register in the host registers module. A soft reset of the transmit
data path will abort all AHB transactions of the transmit data path. The reset bit will be
cleared autonomously by the Ethernet block. A soft reset of the Tx data path will clear
the TxStatus bit in the Status register.
RxReset: Writing a ‘1’ to the RxReset bit will reset the receive data path, excluding the
MAC portions, including all (read-only) registers in the receive data path, as well as
the RxConsumeIndex register in the host registers module. A soft reset of the receive
data path will abort all AHB transactions of the receive data path. The reset bit will be
cleared autonomously by the Ethernet block. A soft reset of the Rx data path will clear
the RxStatus bit in the Status register.
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 August 2010
Chapter 10: LPC17xx Ethernet
UM10360
© NXP B.V. 2010. All rights reserved.
206 of 840