R5F21238DFP#U0 Renesas Electronics America, R5F21238DFP#U0 Datasheet - Page 200

• Manufacturer Part Number: R5F21238DFP#U0
• Description: IC R8C/23 MCU FLASH 48-LQFP
• Manufacturer: Renesas Electronics America
• Series: R8C/2x/23r

Specifications of R5F21238DFP#U0

• Core Size: 16/32-Bit
• Program Memory Size: 64KB (64K x 8)
• Peripherals: POR, Voltage Detect, WDT
• Core Processor: R8C
• Speed: 20MHz
• Connectivity: CAN, I²C, LIN, SIO, SSU, UART/USART
• Number Of I /o: 41
• Program Memory Type: FLASH
• Ram Size: 3K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• No. Of I/o's: 41
• Ram Memory Size: 3KB
• Cpu Speed: 20MHz
• No. Of Timers: 4
• Digital Ic Case Style: LQFP
• Embedded Interface Type: CAN, I2C, UART
• Rohs Compliant: Yes
• Cpu Family: R8C
• Device Core Size: 16b
• Frequency (max): 20MHz
• Interface Type: I2C/UART
• Total Internal Ram Size: 3KB
• # I/os (max): 41
• Number Of Timers - General Purpose: 5
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3V
• On-chip Adc: 12-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: RCDK8C - KIT DEV EVAL FOR CAN R8C/23R0K521237S000BE - KIT DEV RSK R8C/23R0E521237CPE00 - EMULATOR COMPACT R8C/20/21/22/23
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

R8C/22 Group, R8C/23 Group
Rev.2.00 Aug 20, 2008
REJ09B0251-0200
14.3.4
In the output compare function, PWM mode, reset synchronous PWM mode, complementary PWM mode and
PWM3 mode, the TRDIOji output pin can be forcibly set to the programmable I/O port by the INT0 pin input,
and pulse output can be cut off.
The used pins for the output in these functions or modes can function as the output pin of Timer RD when
setting the applicable bit in the TRDOER1 register to 0 (enable Timer RD output). When the PTO bit in the
TRDOER2 register to 1 (INT0 of pulse output forced cutoff signal input enabled), all bits in the TRDOER1
register are set to 1 (disable Timer RD output, the TRDIOji output pin is used as the programmable I/O port)
after “L” is applied to the INT0 pin. The TRDIOji output pin is set to the programmable I/O port after “L” is
applied to the INT0 pin and waiting for 1 to 2 cycles of the Timer RD operation clock (refer to Table 14.11
Timer RD Operation Clocks).
Set as below when using this function:
According to the selection of the POL bit in the INT0IC register and change of the INT0 pin input, the IR bit in
the INT0IC register is set to 1 (interrupt request). Refer to 12. Interrupts for details of interrupts.
• Set the pin status (high impedance, “L” or “H” output) with the pulse output forced cutoff by the P2 and
• Set the INT0EN bit in the INTEN register to 1 (enable INT0 input) and the INT0PL bit to 0 (one edge).
• Set the PD4_5 bit in the PD4 register to 0 (input mode).
• Set the INT0 digital filter by the INT0F1 to INT0F0 bits in the INTF register.
• Set the PTO bit in the TRDOER2 register to 1 (enable pulse output forced cutoff signal input INT0).
PD2 registers.
Pulse Output Forced Cutoff
Page 178 of 501
14. Timers