ATSAM3U4CA-CU Atmel, ATSAM3U4CA-CU Datasheet - Page 224

• Manufacturer Part Number: ATSAM3U4CA-CU
• Description: IC MCU 32BIT 256KB FLSH 100TFBGA
• Manufacturer: Atmel
• Series: SAM3Ur

Specifications of ATSAM3U4CA-CU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 96MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 57
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 52K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b, 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 52 KB
• Interface Type: 3xUSART, TWI, 4xSPI, Bus
• Maximum Clock Frequency: 96 MHz
• Number Of Programmable I/os: 57
• Number Of Timers: 8
• Operating Supply Voltage: 1.62 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3U-EK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

13.22.8.3
13.22.8.4
13.22.9
224
SAM3U Series
MPU design hints and tips
Subregions
Example of SRD use
Regions of 256 bytes or more are divided into eight equal-sized subregions. Set the correspond-
ing bit in the SRD field of the RASR to disable a subregion, see
Register” on page
significant bit controls the last subregion. Disabling a subregion means another region overlap-
ping the disabled range matches instead. If no other enabled region overlaps the disabled
subregion the MPU issues a fault.
Regions of 32, 64, and 128 bytes do not support subregions, With regions of these sizes, you
must set the SRD field to 0x00, otherwise the MPU behavior is Unpredictable.
Two regions with the same base address overlap. Region one is 128KB, and region two is
512KB. To ensure the attributes from region one apply to the first128KB region, set the SRD
field for region two to b00000011 to disable the first two subregions, as
Figure 13-9. SRD use
To avoid unexpected behavior, disable the interrupts before updating the attributes of a region
that the interrupt handlers might access.
Ensure software uses aligned accesses of the correct size to access MPU registers:
The processor does not support unaligned accesses to MPU registers.
When setting up the MPU, and if the MPU has previously been programmed, disable unused
regions to prevent any previous region settings from affecting the new MPU setup.
• except for the RASR, it must use aligned word accesses
• for the RASR it can use byte or aligned halfword or word accesses.
Base address of both regions
219. The least significant bit of SRD controls the first subregion, and the most
; and Region Attribute, Size and Enable
Region 1
Disabled subregion
Disabled subregion
Region 2, with
subregions
“MPU Region Attribute and Size
Figure 13-9
512KB
448KB
384KB
320KB
256KB
192KB
128KB
Offset from
base address
64KB
6430D–ATARM–25-Mar-11
0
shows