ATSAM3U4CA-CU Atmel, ATSAM3U4CA-CU Datasheet - Page 179

• Manufacturer Part Number: ATSAM3U4CA-CU
• Description: IC MCU 32BIT 256KB FLSH 100TFBGA
• Manufacturer: Atmel
• Series: SAM3Ur

Specifications of ATSAM3U4CA-CU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 96MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 57
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 52K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b, 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 52 KB
• Interface Type: 3xUSART, TWI, 4xSPI, Bus
• Maximum Clock Frequency: 96 MHz
• Number Of Programmable I/os: 57
• Number Of Timers: 8
• Operating Supply Voltage: 1.62 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3U-EK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

13.19.10 NVIC design hints and tips
13.19.10.1
6430D–ATARM–25-Mar-11
NVIC programming hints
Ensure software uses correctly aligned register accesses. The processor does not support
unaligned accesses to NVIC registers. See the individual register descriptions for the supported
access sizes.
A interrupt can enter pending state even it is disabled.
Before programming VTOR to relocate the vector table, ensure the vector table entries of the
new vector table are setup for fault handlers and all enabled exception like interrupts. For more
information see
Software uses the CPSIE I and CPSID I instructions to enable and disable interrupts. The
CMSIS provides the following intrinsic functions for these instructions:
In addition, the CMSIS provides a number of functions for NVIC control, including:
Table 13-29. CMSIS functions for NVIC control
For more information about these functions see the CMSIS documentation.
CMSIS interrupt control function
void NVIC_SetPriorityGrouping(uint32_t
priority_grouping)
void NVIC_EnableIRQ(IRQn_t IRQn)
void NVIC_DisableIRQ(IRQn_t IRQn)
uint32_t NVIC_GetPendingIRQ (IRQn_t IRQn)
void NVIC_SetPendingIRQ (IRQn_t IRQn)
void NVIC_ClearPendingIRQ (IRQn_t IRQn)
uint32_t NVIC_GetActive (IRQn_t IRQn)
void NVIC_SetPriority (IRQn_t IRQn, uint32_t priority)
uint32_t NVIC_GetPriority (IRQn_t IRQn)
void NVIC_SystemReset (void)
void __disable_irq(void) // Disable Interrupts
void __enable_irq(void) // Enable Interrupts
“Vector Table Offset Register” on page
Return true if IRQn is pending
Set priority for IRQn
Read priority of IRQn
Description
Set the priority grouping
Enable IRQn
Disable IRQn
Set IRQn pending
Clear IRQn pending status
Return the IRQ number of the active
interrupt
Reset the system
186.
SAM3U Series
179