ATSAM3U4CA-CU Atmel, ATSAM3U4CA-CU Datasheet - Page 139

• Manufacturer Part Number: ATSAM3U4CA-CU
• Description: IC MCU 32BIT 256KB FLSH 100TFBGA
• Manufacturer: Atmel
• Series: SAM3Ur

Specifications of ATSAM3U4CA-CU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 96MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 57
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 52K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 4x10b, 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFBGA
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 52 KB
• Interface Type: 3xUSART, TWI, 4xSPI, Bus
• Maximum Clock Frequency: 96 MHz
• Number Of Programmable I/os: 57
• Number Of Timers: 8
• Operating Supply Voltage: 1.62 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3U-EK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

13.14 Saturating instructions
13.14.1
13.14.1.1
13.14.1.2
6430D–ATARM–25-Mar-11
SSAT and USAT
Syntax
Operation
This section describes the saturating instructions, SSAT and USAT.
Signed Saturate and Unsigned Saturate to any bit position, with optional shift before saturating.
where:
op
cond
Rd
n
Rm
shift #s
These instructions saturate to a signed or unsigned n-bit value.
The SSAT instruction applies the specified shift, then saturates to the signed range −
2
The USAT instruction applies the specified shift, then saturates to the unsigned range 0 ≤x ≤2
For signed n-bit saturation using SSAT, this means that:
For unsigned n-bit saturation using USAT, this means that:
If the returned result is different from the value to be saturated, it is called saturation. If satura-
tion occurs, the instruction sets the Q flag to 1 in the APSR. Otherwise, it leaves the Q flag
unchanged. To clear the Q flag to 0, you must use the MSR instruction, see
To read the state of the Q flag, use the MRS instruction, see
n–1
• if the value to be saturated is less than − 2
• if the value to be saturated is greater than 2
• otherwise, the result returned is the same as the value to be saturated.
• if the value to be saturated is less than 0, the result returned is 0
• if the value to be saturated is greater than 2
• otherwise, the result returned is the same as the value to be saturated.
op{cond} Rd, #n, Rm {, shift #s}
≤x ≤2
SSAT
USAT
n ranges from 1 to 32 for SSAT
n ranges from 0 to 31 for USAT.
ASR #s where s is in the range 1 to 31
LSL #s where s is in the range 0 to 31.
n–1
− 1.
is one of:
Saturates a signed value to a signed range.
Saturates a signed value to an unsigned range.
is an optional condition code, see
is the destination register.
specifies the bit position to saturate to:
is the register containing the value to saturate.
is an optional shift applied to Rm before saturating. It must be one of the following:
n− 1
, the result returned is − 2
n− 1
n
− 1, the result returned is 2
“Conditional execution” on page
− 1, the result returned is 2
“MRS” on page
SAM3U Series
n-1
n
− 1
n-1
“MSR” on page
159.
− 1
100.
160.
139
n
− 1.