TMPA901CMXBG Toshiba, TMPA901CMXBG Datasheet - Page 856

• Manufacturer Part Number: TMPA901CMXBG
• Description: Microcontrollers (MCU) 32-bit RISC MCU 16kb ARM926EJ 16kb 200Mhz
• Manufacturer: Toshiba

Specifications of TMPA901CMXBG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): -
• Rom Type: ROMless
• Ram (kbytes): 32
• Number Of Pins: 177
• Package: BGA
• Vcc: 3V
• Tft Lcd Controller: Y
• Touchscreen Controller: Y
• Usb Host Fs With Phy: Y
• Usb Device Hs With Phy: Y
• Sd Host Controller: -
• Cmos Image Sensor Interface: -
• I2s: 1
• Ssp (ch) Spi: 1
• I2mc/sio (ch): 1
• Uart/sio (ch): 2
• External Bus Interface: Y
• Cs/wait Controller (ch): 4
• Dma Controller: 8
• 10-bit Ad Converter: 4
• 12-bit Da Converter: -
• 16-bit Timer / Counter: 6
• Real Time Clock: Y
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Low-power Modes: Y
• Lead Free Status / Rohs Status: Details

4.6
TMPA900CMXBG
TMPA901CMXBG
MCU
Recommended Oscillation Circuit
information when selecting the resonator to be used.
The TMPA901CM is evaluated by using the resonators shown below. Please use this
MCU
Note: The total load capacitance of the oscillation pins is the sum of the external (or internal) load capacitances
Note 1: Constants C1 and C2 indicates values for the built-in load capacitance type.
Note 2: The part numbers and specifications of Kyocera’s products are updated as occasion requires. For details,
Note 3: When the ceramic resonator is used for high-frequency oscillator circuit, USB device and host controller
Note: The part numbers and specifications of KYOCERA KINSEKI’s products are updated as occasion requires.
(1) Connection example
(2) Recommended ceramic resonator: KYOCERA KINSEKI Corporation
(3) Recommended crystal low-frequency resonator: KYOCERA KINSEKI Corporation
For details, please check the website of KYOCERA KINSEKI.
C1and C2 and the stray capacitance on the circuit board. Even if the recommended C1 and C2 constants are
used, the total load capacitance may vary with each board. In board design, the patterns around the oscillation
circuit must be as short as possible. We also recommend that oscillation evaluations be performed on the
actual board to be used.
please check the website of Murata.
http://global.kyocera.com/
requires using the clock in high precision. In this case, the clock of X1USB pin should be used the clock
precision is 24MHz 100ppm.
Oscillation
frequency
http://global.kyocera.com/
The table below shows the recommended circuit constants of the low-frequency
oscillation circuit.
The table below shows the recommended circuit constants for the high-frequency
oscillation circuit.
27.000
24.000
C1
high-frequency oscillator
[MHZ]
Connection diagram of
Oscillation
frequency
X1
32.768
[kHz]
Type
SMD CX2520SB27000B0HLQZ1
SMD CX2520SB24000C0HLQZ1
Rf
C2
Recommended
Recommended resonator
ST3215SB
X2
resonator
Rd
TMPA901CM- 855
C1
low-frequency oscillator
Connection diagram of
XT1
[pF]
Recommended constants
C1
7
Rf
Recommended constants
[pF]
[pF]
C1
C2
6
7
7
C2
[pF]
XT2
C2
820 Built-In
6
7
Rd
[ ]
Rd
[ ]
Rd
0
[ ]
Rf
Open
[ ]
voltage range [V]
Rf
Power supply
3.0 to 3.6
Recommended operating
voltage range [V]
Power supply
Recommended operating
1.4 to 1.6
conditions
conditions
Temperature
range [ C]
-20 to 85
Temperature
TMPA901CM
range [ C]
-20 to 85
2010-07-29