LPC1313FBD48,151 NXP Semiconductors, LPC1313FBD48,151 Datasheet - Page 219

• Manufacturer Part Number: LPC1313FBD48,151
• Description: IC MCU 32BIT 32KB FLASH 48LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC13xxr

Specifications of LPC1313FBD48,151

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-LQFP
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: I²C, Microwire, SPI, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 42
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC13
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Interface Type: I2C, UART
• Maximum Clock Frequency: 72 MHz
• Number Of Timers: 2
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: OM11041
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: LPC1000
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Total Internal Ram Size: 8KB
• # I/os (max): 42
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: LPC1000
• Maximum Speed: 72 MHz
• Number Of Programmable I/os: 42
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-4918 - KIT DEV FOR LPC1313622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4914; 935289651151

NXP Semiconductors
UM10375
User manual
12.11.4 Slave Transmitter mode
In the slave transmitter mode, a number of data bytes are transmitted to a master receiver
(see
and I2CON have been initialized, the I
address followed by the data direction bit which must be “1” (R) for the I
operate in the slave transmitter mode. After its own slave address and the R bit have been
received, the serial interrupt flag (SI) is set and a valid status code can be read from
I2STAT. This status code is used to vector to a state service routine, and the appropriate
action to be taken for each of these status codes is detailed in
transmitter mode may also be entered if arbitration is lost while the I
master mode (see state 0xB0).
If the AA bit is reset during a transfer, the I
and enter state 0xC0 or 0xC8. The I
and will ignore the master receiver if it continues the transfer. Thus the master receiver
receives all 1s as serial data. While AA is reset, the I
slave address or a General Call address. However, the I
address recognition may be resumed at any time by setting AA. This means that the AA
bit may be used to temporarily isolate the I
Figure
33). Data transfer is initialized as in the slave receiver mode. When I2ADR
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 7 July 2010
2
C block is switched to the not addressed slave mode
2
C block waits until it is addressed by its own slave
2
C block will transmit the last byte of the transfer
2
C block from the I
Chapter 12: LPC13xx I2C-bus controller
2
C block does not respond to its own
2
C-bus is still monitored, and
2
C-bus.
Table
2
231. The slave
C block is in the
UM10375
© NXP B.V. 2010. All rights reserved.
2
C block to
221 of 333