LPC1313FBD48,151 NXP Semiconductors, LPC1313FBD48,151 Datasheet - Page 170

• Manufacturer Part Number: LPC1313FBD48,151
• Description: IC MCU 32BIT 32KB FLASH 48LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC13xxr

Specifications of LPC1313FBD48,151

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-LQFP
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: I²C, Microwire, SPI, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 42
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC13
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Interface Type: I2C, UART
• Maximum Clock Frequency: 72 MHz
• Number Of Timers: 2
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: OM11041
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: LPC1000
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Total Internal Ram Size: 8KB
• # I/os (max): 42
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: LPC1000
• Maximum Speed: 72 MHz
• Number Of Programmable I/os: 42
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-4918 - KIT DEV FOR LPC1313622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4914; 935289651151

NXP Semiconductors
UM10375
User manual
11.6.5 UART Interrupt Identification Register (U0IIR - 0x4004 8008, Read
Only)
U0IIR provides a status code that denotes the priority and source of a pending interrupt.
The interrupts are frozen during a U0IIR access. If an interrupt occurs during a U0IIR
access, the interrupt is recorded for the next U0IIR access.
Table 192. UART Interrupt Identification Register (U0IIR - address 0x4004 8008, Read Only)
Bits U0IIR[9:8] are set by the auto-baud function and signal a time-out or end of auto-baud
condition. The auto-baud interrupt conditions are cleared by setting the corresponding
Clear bits in the Auto-baud Control Register.
If the IntStatus bit is one and no interrupt is pending and the IntId bits will be zero. If the
IntStatus is 0, a non auto-baud interrupt is pending in which case the IntId bits identify the
type of interrupt and handling as described in
interrupt handler routine can determine the cause of the interrupt and how to clear the
active interrupt. The U0IIR must be read in order to clear the interrupt prior to exiting the
Interrupt Service Routine.
The UART RLS interrupt (U0IIR[3:1] = 011) is the highest priority interrupt and is set
whenever any one of four error conditions occur on the UART RX input: overrun error
(OE), parity error (PE), framing error (FE) and break interrupt (BI). The UART Rx error
condition that set the interrupt can be observed via U0LSR[4:1]. The interrupt is cleared
upon a U0LSR read.
Bit
0
3:1
5:4
7:6
8
9
31:10 -
Symbol
IntStatus
IntId
-
FIFO Enable
ABEOInt
ABTOInt
bit description
All information provided in this document is subject to legal disclaimers.
Value Description
011
010
110
001
000
0
1
Rev. 2 — 7 July 2010
Interrupt status. Note that U0IIR[0] is active low. The
pending interrupt can be determined by evaluating
U0IIR[3:1].
At least one interrupt is pending.
No interrupt is pending.
Interrupt identification. U0IER[3:1] identifies an interrupt
corresponding to the UART Rx FIFO. All other combinations
of U0IER[3:1] not listed below are reserved (100,101,111).
1 - Receive Line Status (RLS).
2a - Receive Data Available (RDA).
2b - Character Time-out Indicator (CTI).
3 - THRE Interrupt.
4 - Modem interrupt.
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
These bits are equivalent to U0FCR[0].
End of auto-baud interrupt. True if auto-baud has finished
successfully and interrupt is enabled.
Auto-baud time-out interrupt. True if auto-baud has timed
out and interrupt is enabled.
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
Table
193. Given the status of U0IIR[3:0], an
Chapter 11: LPC13xx UART
UM10375
© NXP B.V. 2010. All rights reserved.
172 of 333
Reset
value
1
0
NA
0
0
0
NA