LPC1313FBD48,151 NXP Semiconductors, LPC1313FBD48,151 Datasheet - Page 166

• Manufacturer Part Number: LPC1313FBD48,151
• Description: IC MCU 32BIT 32KB FLASH 48LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC13xxr

Specifications of LPC1313FBD48,151

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 48-LQFP
• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: I²C, Microwire, SPI, SSI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 42
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC13
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Interface Type: I2C, UART
• Maximum Clock Frequency: 72 MHz
• Number Of Timers: 2
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: OM11041
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: LPC1000
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 72MHz
• Total Internal Ram Size: 8KB
• # I/os (max): 42
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: LPC1000
• Maximum Speed: 72 MHz
• Number Of Programmable I/os: 42
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-4918 - KIT DEV FOR LPC1313622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4914; 935289651151

NXP Semiconductors
11.5 Clocking and power control
11.6 Register description
UM10375
User manual
The clocks and power to the UART block are controlled by two registers:
Remark: The UART pins must be configured in the corresponding IOCON registers
before the UART clocks are enabled.
The UART contains registers organized as shown in
Bit (DLAB) is contained in U0LCR[7] and enables access to the Divisor Latches.
1. The UART block can be enabled or disabled through the System AHB clock control
2. The UART peripheral clock UART_PCLK is enabled in the UART clock divider
register bit 12 (see
register (see
All information provided in this document is subject to legal disclaimers.
Table
25). This clock is used by the UART baud rate generator.
Table
Rev. 2 — 7 July 2010
23).
Table
186. The Divisor Latch Access
Chapter 11: LPC13xx UART
UM10375
© NXP B.V. 2010. All rights reserved.
168 of 333