OM13013,598 NXP Semiconductors, OM13013,598 Datasheet - Page 283
OM13013,598
Manufacturer Part Number
OM13013,598
Description
BOARD DEMO IAR LPC1227 JLINKLITE
Manufacturer
NXP Semiconductors
Series
-r
Specifications of OM13013,598
Design Resources
LPC122x-SK Brd Schematic
Processor To Be Evaluated
LPC1227
Processor Series
LPC122x
Data Bus Width
32 bit
Interface Type
UART, SSP, SPI, I2C
Cpu Core
ARM Cortex-M0
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
3 V to 3.6 V
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
568-6885
- Current page: 283 of 442
- Download datasheet (3Mb)
NXP Semiconductors
Table 265. Watchdog operating modes selection
UM10441
User manual
WDEN
0
1
1
WDRESET
X (0 or 1)
0
1
17.7.2 Watchdog Timer Constant register
17.7.3 Watchdog Feed register
The TC register determines the time-out value. Every time a feed sequence occurs, the
TC content is reloaded into the Watchdog timer. This is pre-loaded with the value 0x00
FFFF upon reset. Writing values below 0xFF will cause 0xFF to be loaded into the TC.
Thus the minimum time-out interval is T
If the WDPROTECT bit in MOD = 1, an attempt to change the value of TC before the
watchdog counter is below the values of WARNINT and WINDOW will cause a watchdog
reset and set the WDTOF flag.
Table 266. Watchdog Timer Constant register (TC - 0x4000 4004) bit description
Writing 0xAA followed by 0x55 to this register will reload the Watchdog timer with the
WDTC value. This operation will also start the Watchdog if it is enabled via the WDMOD
register. Setting the WDEN bit in the WDMOD register is not sufficient to enable the
Watchdog. A valid feed sequence must be completed after setting WDEN before the
Watchdog is capable of generating a reset. Until then, the Watchdog will ignore feed
errors. After writing 0xAA to WDFEED, access to any Watchdog register other than writing
0x55 to WDFEED causes an immediate reset/interrupt when the Watchdog is enabled,
and sets the WDTOF flag. The reset will be generated during the second PCLK following
an incorrect access to a Watchdog register during a feed sequence.
Interrupts should be disabled during the feed sequence. An abort condition will occur if an
interrupt happens during the feed sequence.
Table 267. Watchdog Feed register (FEED - 0x4000 4008) bit description
Mode of Operation
Debug/Operate without the Watchdog running.
Watchdog interrupt mode: the watchdog warning interrupt will be generated but watchdog reset will
not.
When this mode is selected, the watchdog counter reaching the value specified by WDWARNINT
will set the WDINT flag and the Watchdog interrupt request will be generated.
Watchdog reset mode: both the watchdog interrupt and watchdog reset are enabled.
When this mode is selected, the watchdog counter reaching the value specified by WDWARNINT
will set the WDINT flag and the Watchdog interrupt request will be generated. The watchdog
counter reaching zero will reset the microcontroller.
Other causes for a watchdog reset are: A watchdog feed or changing the WDTC value (if the
WDPROTECT bit is set in the MOD register) before reaching the value of WDWINDOW.
Bit
23:0
31:24
Bit
7:0
31:8
Symbol
WDTC
-
Symbol
Feed
-
All information provided in this document is subject to legal disclaimers.
Description
Watchdog time-out interval.
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
Description
Feed value should be 0xAA followed by 0x55.
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
Rev. 1 — 15 February 2011
Chapter 17: LPC122x Windowed Watchdog Timer (WWDT)
WDCLK
× 256 × 4.
UM10441
© NXP B.V. 2011. All rights reserved.
Reset value
-
-
Reset value
0x00 FFFF
-
283 of 442
Related parts for OM13013,598
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: