OM13013,598 NXP Semiconductors, OM13013,598 Datasheet - Page 145
OM13013,598
Manufacturer Part Number
OM13013,598
Description
BOARD DEMO IAR LPC1227 JLINKLITE
Manufacturer
NXP Semiconductors
Series
-r
Specifications of OM13013,598
Design Resources
LPC122x-SK Brd Schematic
Processor To Be Evaluated
LPC1227
Processor Series
LPC122x
Data Bus Width
32 bit
Interface Type
UART, SSP, SPI, I2C
Cpu Core
ARM Cortex-M0
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
3 V to 3.6 V
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
568-6885
- Current page: 145 of 442
- Download datasheet (3Mb)
NXP Semiconductors
UM10441
User manual
Fig 5.
UART Rx
UART Rx
UART Rx
FIFO read
FIFO level
RTS pin
Auto-RTS Functional Timing
9.5.8.1.2 Auto-CTS
start
N-1
byte N
If Auto-RTS mode is disabled, the RTSen bit controls the RTS output of the UART. If
Auto-RTS mode is enabled, hardware controls the RTS output, and the actual value of
RTS will be copied in the RTS Control bit of the UART. As long as Auto-RTS is enabled,
the value of the RTS Control bit is read-only for software.
Example: Suppose the UART operating in type ‘550 mode has the trigger level in FCR set
to 0x2, then, if Auto-RTS is enabled, the UART will deassert the RTS output as soon as
the receive FIFO contains 8 bytes
reasserted as soon as the receive FIFO hits the previous trigger level: 4 bytes.
The Auto-CTS function is enabled by setting the CTSen bit. If Auto-CTS is enabled the
transmitter circuitry in the TSR module checks CTS input before sending the next data
byte. When CTS is active (low), the transmitter sends the next byte. To stop the
transmitter from sending the following byte, CTS must be released before the middle of
the last stop bit that is currently being sent. In Auto-CTS mode a change of the CTS signal
does not trigger a modem status interrupt unless the CTS Interrupt Enable bit is set, Delta
CTS bit in the MSR will be set though.
Modem Status interrupt.
Table 148. Modem status interrupt generation
Enable
modem
status
interrupt
(ER[3])
0
1
1
1
1
1
1
1
1
stop
start
N
CTSen
(MCR[7])
x
0
0
0
1
1
1
1
1
All information provided in this document is subject to legal disclaimers.
bits0..7
N-1
Rev. 1 — 15 February 2011
CTS
interrupt
enable
(IER[7])
x
x
x
x
0
0
1
1
1
stop
N-2
N-1
(Table 145 on page
Chapter 9: LPC122x UART0 with modem control
Delta CTS
(MSR[0])
x
0
1
x
x
x
0
1
x
Table 148
N-2
lists the conditions for generating a
Delta DCD or trailing edge
RI or
Delta DSR (MSR[3] or
MSR[2] or MSR[1])
x
0
x
1
0
1
0
x
1
M+2
142). The RTS output will be
M+1
M
start
UM10441
© NXP B.V. 2011. All rights reserved.
bits0..7
M-1
Modem
status
interrupt
No
No
Yes
Yes
No
Yes
No
Yes
Yes
145 of 442
stop
Related parts for OM13013,598
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: