OM13013,598 NXP Semiconductors, OM13013,598 Datasheet - Page 213
OM13013,598
Manufacturer Part Number
OM13013,598
Description
BOARD DEMO IAR LPC1227 JLINKLITE
Manufacturer
NXP Semiconductors
Series
-r
Specifications of OM13013,598
Design Resources
LPC122x-SK Brd Schematic
Processor To Be Evaluated
LPC1227
Processor Series
LPC122x
Data Bus Width
32 bit
Interface Type
UART, SSP, SPI, I2C
Cpu Core
ARM Cortex-M0
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
3 V to 3.6 V
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
568-6885
- Current page: 213 of 442
- Download datasheet (3Mb)
NXP Semiconductors
UM10441
User manual
11.10.7.1 Simultaneous repeated START conditions from two masters
11.10.7.2 Data transfer after loss of arbitration
11.10.7.3 Forced access to the I
A repeated START condition may be generated in the master transmitter or master
receiver modes. A special case occurs if another master simultaneously generates a
repeated START condition (see
either master since they were both transmitting the same data.
If the I
a repeated START condition itself, it will release the bus, and no interrupt request is
generated. If another master frees the bus by generating a STOP condition, the I
will transmit a normal START condition (state 0x08), and a retry of the total serial data
transfer can commence.
Arbitration may be lost in the master transmitter and master receiver modes (see
Figure
0x78, and 0xB0 (see
If the STA flag in CON is set by the routines which service these states, then, if the bus is
free again, a START condition (state 0x08) is transmitted without intervention by the CPU,
and a retry of the total serial transfer can commence.
In some applications, it may be possible for an uncontrolled source to cause a bus
hang-up. In such situations, the problem may be caused by interference, temporary
interruption of the bus or a temporary short-circuit between SDA and SCL.
If an uncontrolled source generates a superfluous START or masks a STOP condition,
then the I
obtained within a reasonable amount of time, then a forced access to the I
possible. This is achieved by setting the STO flag while the STA flag is still set. No STOP
condition is transmitted. The I
and is able to transmit a START condition. The STO flag is cleared by hardware
Figure
08H
Fig 26. Simultaneous repeated START conditions from two masters
S
2
20). Loss of arbitration is indicated by the following states in STAT; 0x38, 0x68,
27.
C hardware detects a repeated START condition on the I
SLA
2
C-bus stays busy indefinitely. If the STA flag is set and bus access is not
W
All information provided in this document is subject to legal disclaimers.
18H
A
Figure 22
Rev. 1 — 15 February 2011
DATA
2
C-bus
2
C hardware behaves as if a STOP condition was received
and
repeated START earlier
Figure
other Master sends
28H
A
Figure
26). Until this occurs, arbitration is not lost by
S
23).
Chapter 11: LPC122x I2C-bus controller
OTHER MASTER
CONTINUES
2
C-bus before generating
retry
08H
P
UM10441
© NXP B.V. 2011. All rights reserved.
S
2
C-bus is
SLA
2
213 of 442
C block
Related parts for OM13013,598
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: