UPD70F3786GJ-GAE-AX Renesas Electronics America, UPD70F3786GJ-GAE-AX Datasheet - Page 821

• Manufacturer Part Number: UPD70F3786GJ-GAE-AX
• Description: MCU 32BIT V850ES/JX3-E 144-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Er

Specifications of UPD70F3786GJ-GAE-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: CAN, CSI, EBI/EMI, Ethernet, I²C, UART/USART, USB
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 100
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 124K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

17.6.2 SBF transmission/reception format
enable use of the LIN function.
The V850ES/JH3-E and V850ES/JJ3-E have an SBF (Sync Break Field) transmission/reception control function to
Remark
LIN
bus
TXDCn (output)
INTUCnT
interrupt
Notes 1. The interval between each field is controlled by software.
Remark
Figures 17-11 and 17-12 outline the transmission and reception manipulations of LIN.
2. SBF output is performed by hardware.
3. 80H transfer in the 8-bit mode is substituted for the wakeup signal frame.
4. A transmission enable interrupt request signal (INTUCnT) is output at the start of each transmission.
LIN stands for Local Interconnect Network and is a low-speed (1 to 20 kbps) serial communication
protocol intended to aid the cost reduction of an automotive network.
LIN communication is single-master communication, and up to 15 slaves can be connected to one
master.
The LIN slaves are used to control the switches, actuators, and sensors, and these are connected to the
LIN master via the LIN network.
Normally, the LIN master is connected to a network such as CAN (Controller Area Network).
In addition, the LIN bus uses a single-wire method and is connected to the nodes via a transceiver that
complies with ISO9141.
In the LIN protocol, the master transmits a frame with baud rate information and the slave receives it and
corrects the baud rate error. Therefore, communication is possible when the baud rate error in the slave
is ±15% or less.
UCnOPT0.UCnSLS2 to UCnOPT0.UCnSLS0 bits.
required,
UCnCTL2.UCnBRS0 bits.
The INTUCnT signal is also output at the start of each SBF transmission.
n = 0 to 5 (V850ES/JH3-E)
n = 0 to 7 (V850ES/JJ3-E)
Wake-up
Note 3
8 bits
signal
frame
such
CHAPTER 17 ASYNCHRONOUS SERIAL INTERFACE C (UARTC)
Note 1
Figure 17-11. LIN Transmission Manipulation Outline
SBF transmission
adjustments
Note 2
13 bits
break
Sync
field
Note 4
User’s Manual U19601EJ2V0UD
can
transmission
be
Sync
55H
field
performed
The output width is the bit length set by the
transmission
Identifier
If even finer output width adjustments are
Data
field
using
transmission
DATA
Data
field
the
UCnCTL2.UCnBRS7
transmission
DATA
Data
field
transmission
Check
SUM
field
Data
to
819