UPD70F3786GJ-GAE-AX Renesas Electronics America, UPD70F3786GJ-GAE-AX Datasheet - Page 1627

• Manufacturer Part Number: UPD70F3786GJ-GAE-AX
• Description: MCU 32BIT V850ES/JX3-E 144-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Er

Specifications of UPD70F3786GJ-GAE-AX

• Core Processor: RISC
• Core Size: 32-Bit
• Speed: 50MHz
• Connectivity: CAN, CSI, EBI/EMI, Ethernet, I²C, UART/USART, USB
• Peripherals: DMA, LVD, PWM, WDT
• Number Of I /o: 100
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 124K x 8
• Voltage - Supply (vcc/vdd): 2.85 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

27.8 Sub-IDLE Mode
27.8.1 Setting and operation status
bit to 1 in the subclock operation mode.
chip peripheral functions is stopped.
retained. The CPU and the other on-chip peripheral functions are stopped. However, the on-chip peripheral functions
that can operate with the subclock or an external clock continue operating.
can reduce the power consumption more than the subclock operation mode. If the sub-IDLE mode is set after the
main clock has been stopped, the current consumption can be reduced to a level as low as that in the STOP mode.
27.8.2 Releasing sub-IDLE mode
unmasked external interrupt request signal (INTPn pin input), unmasked internal interrupt request signal from the
peripheral functions operable in the sub-IDLE mode, or reset signal (reset by RESET pin input, WDT2RES signal, low-
voltage detector (LVI), or clock monitor (CLM)). The PLL returns to the operating status it was in before the sub-IDLE
mode was set.
The sub-IDLE mode is set by setting the PSMR.PSM1 and PSMR.PSM0 bits to 00 or 10 and setting the PSC.STP
In this mode, the clock oscillator continues operating but clock supply to the CPU, flash memory, and the other on-
As a result, program execution stops and the contents of the internal RAM before the sub-IDLE mode was set are
Because the sub-IDLE mode stops operation of the CPU, flash memory, and other on-chip peripheral functions, it
Table 27-12 shows the operating status in the sub-IDLE mode.
Cautions 1. Following the store instruction to the PSC register for setting the sub-IDLE mode, insert the
The sub-IDLE mode is released by a non-maskable interrupt request signal (NMI pin input, INTWDT2 signal),
When the sub-IDLE mode is released by an interrupt request signal, the subclock operation mode is set.
(1) Releasing sub-IDLE mode by non-maskable interrupt request signal or unmasked maskable interrupt
request signal
The sub-IDLE mode is released by a non-maskable interrupt request signal or an unmasked maskable
interrupt request signal, regardless of the priority of the interrupt request signal.
If the sub-IDLE mode is set in an interrupt servicing routine, however, an interrupt request signal that is issued
later is serviced as follows.
(a) If an interrupt request signal with a priority lower than that of the interrupt request currently being serviced
(b) If an interrupt request signal with a priority higher than that of the interrupt request currently being serviced
Cautions 1. The interrupt request signal that is disabled by setting the PSC.NMI1M, PSC.NMI0M, and
Remark
is issued, the sub-IDLE mode is released, but that interrupt request signal is not acknowledged. The
interrupt request signal itself is retained.
is issued (including a non-maskable interrupt request signal), the sub-IDLE mode is released and that
interrupt request signal is acknowledged.
2. If the sub-IDLE mode is set while an unmasked interrupt request signal is being held pending,
five or more NOP instructions.
the sub-IDLE mode is then released immediately by the pending interrupt request.
n = 00 to 20: V850ES/JH3-E
n = 00 to 25: V850ES/JJ3-E
2. When the sub-IDLE mode is released, 12 cycles of the subclock (about 366
PSC.INTM bits to 1 becomes invalid and sub-IDLE mode is not released.
from when the interrupt request signal that releases the sub-IDLE mode is generated to
when the mode is released.
CHAPTER 27 STANDBY FUNCTION
User’s Manual U19601EJ2V0UD
μ
s) elapse
1625