MMC2114CFCAG33 Freescale Semiconductor, MMC2114CFCAG33 Datasheet - Page 195

• Manufacturer Part Number: MMC2114CFCAG33
• Description: IC MCU 32BIT 33MHZ 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: MCorer

Specifications of MMC2114CFCAG33

• Core Processor: M210
• Core Size: 32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 67
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Processor Series: MMC2114
• Core: M-CORE
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 104
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Controller Family/series: MCORE
• No. Of I/o's: 104
• Ram Memory Size: 32KB
• Cpu Speed: 33MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

8.8.4 Interrupt Configuration
8.8.4.1 CPU Configuration
8.8.4.2 Interrupt Controller Configuration
MMC2114 • MMC2113 • MMC2112 — Rev. 1.0
MOTOROLA
NOTE:
After reset, all interrupts are disabled by default. To properly configure
the system to handle interrupt requests, configuration must be
performed at three levels:
Configure the CPU first, the interrupt controller second, and the local
interrupt sources last.
For fast interrupts, set the FIE[x] bit in FIER in the CPU. For normal
interrupts, set the NIE[x] bit. Both FIE and NIE are cleared at reset.
To allow long latency, multicycle instructions to be interrupted before
completion, set the IC bit in the PSR.
VBR in the CPU defines the base address of the exception vector table.
If autovectors are to be used, then initialize the INT and FINT
autovectors (vector numbers 10 and 11, respectively). If vectored
interrupts are to be used, then initialize the vectored interrupts (vector
numbers 32–63 and/or 64–95). Whether 32 or 64 vectors are required
depends on whether the fast interrupts share vectors with the normal
interrupt sources based on the FVE bit in the interrupt controller ICR.
For each vector number, create an interrupt service routine to service
the interrupt, clear the local interrupt flag, and return from the interrupt
routine.
By default, each interrupt source to the interrupt controller is assigned a
priority level of 0 and disabled. Each interrupt source can be
programmed to one of 32 priority levels and enabled as either a fast or
normal interrupt source. Also, the FVE and AE bits in ICR can be
programmed to select autovectored/vectored interrupts and also
•
•
•
Freescale Semiconductor, Inc.
For More Information On This Product,
CPU
Interrupt controller
Local interrupt sources
Go to: www.freescale.com
Interrupt Controller Module
Interrupt Controller Module
Functional Description
Advance Information
195