LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 456

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
4.11 UART1 Line Status Register (U1LSR - 0xE001 0014, Read Only)
The U1LSR is a read-only register that provides status information on the UART1 TX and
RX blocks.
Table 408. UART1 Line Status Register (U1LSR - address 0xE001 0014, Read Only) bit
Bit Symbol
0
1
2
3
4
Receiver
Data
Ready
(RDR)
Overrun
Error
Parity
Error
Framing
Error
Break
Interrupt
(OE)
(PE)
(FE)
(BI)
description
Value Description
0
1
0
1
0
1
0
1
0
1
Rev. 04 — 26 August 2009
U1LSR[0] is set when the U1RBR holds an unread character and
is cleared when the UART1 RBR FIFO is empty.
U1RBR is empty.
U1RBR contains valid data.
The overrun error condition is set as soon as it occurs. An U1LSR
read clears U1LSR[1]. U1LSR[1] is set when UART1 RSR has a
new character assembled and the UART1 RBR FIFO is full. In
this case, the UART1 RBR FIFO will not be overwritten and the
character in the UART1 RSR will be lost.
Overrun error status is inactive.
Overrun error status is active.
When the parity bit of a received character is in the wrong state, a
parity error occurs. An U1LSR read clears U1LSR[2]. Time of
parity error detection is dependent on U1FCR[0].
Note: A parity error is associated with the character at the top of
the UART1 RBR FIFO.
Parity error status is inactive.
Parity error status is active.
When the stop bit of a received character is a logic 0, a framing
error occurs. An U1LSR read clears U1LSR[3]. The time of the
framing error detection is dependent on U1FCR0. Upon detection
of a framing error, the RX will attempt to resynchronize to the data
and assume that the bad stop bit is actually an early start bit.
However, it cannot be assumed that the next received byte will be
correct even if there is no Framing Error.
Note: A framing error is associated with the character at the top
of the UART1 RBR FIFO.
Framing error status is inactive.
Framing error status is active.
When RXD1 is held in the spacing state (all 0’s) for one full
character transmission (start, data, parity, stop), a break interrupt
occurs. Once the break condition has been detected, the receiver
goes idle until RXD1 goes to marking state (all 1’s). An U1LSR
read clears this status bit. The time of break detection is
dependent on U1FCR[0].
Note: The break interrupt is associated with the character at the
top of the UART1 RBR FIFO.
Break interrupt status is inactive.
Break interrupt status is active.
Chapter 17: LPC24XX UART1
UM10237
© NXP B.V. 2009. All rights reserved.
456 of 792
Reset
Value
0
0
0
0
0