LPC2458FET180,551 NXP Semiconductors, LPC2458FET180,551 Datasheet - Page 352

• Manufacturer Part Number: LPC2458FET180,551
• Description: IC ARM7 MCU FLASH 512K 180TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC2400r

Specifications of LPC2458FET180,551

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 72MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 136
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 98K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 180-TFBGA
• Processor Series: LPC24
• Core: ARM7TDMI-S
• Data Bus Width: 32 bit
• Data Ram Size: 98 KB
• Interface Type: CAN, Ethernet, I2C, I2S, IrDA, SPI, SSP, UART, USB
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 136
• Number Of Timers: 4
• Operating Supply Voltage: 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, SAB-TFBGA180
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 10 bit, 1 Channel
• Package: 180TFBGA
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 72 MHz
• For Use With: 622-1023 - BOARD SCKT ADAPTER FOR TFBGA180622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4258; 935282454551; LPC2458FET180-S

NXP Semiconductors
UM10237_4
User manual
9.6.5 USB Control register (USBCtrl - 0xFFE0 C228)
9.7.1 USB Command Code register (USBCmdCode - 0xFFE0 C210)
9.7 SIE command code registers
Table 324. USB Transmit Packet Length register (USBTxPLen - address 0xFFE0 C224) bit
This register controls the data transfer operation of the USB device. It selects the endpoint
buffer that is accessed by the USBRxData and USBTxData registers, and enables
reading and writing them. USBCtrl is a read/write register.
Table 325. USB Control register (USBCtrl - address 0xFFE0 C228) bit description
The SIE command code registers are used for communicating with the Serial Interface
Engine. See
information.
This register is used for sending the command and write data to the SIE. The commands
written here are propagated to the SIE and executed there. After executing the command,
the register is empty, and the CCEMPTY bit of USBDevIntSt register is set. See
Section 13–11
Bit
9:0
31:10 -
Bit
0
1
5:2
31:6 -
Symbol
RD_EN
WR_EN
LOG_ENDPOINT -
Symbol
PKT_LNGTH -
description
Section 13–11 “Serial interface engine command description”
for details. USBCmdCode is a write only register.
Value Description
-
Rev. 04 — 26 August 2009
Value
0
1
0
1
-
The remaining number of bytes to be written to the
selected endpoint buffer. This field is decremented by 4 by
hardware after each write to USBTxData. When this field
decrements to 0, the TxENDPKT bit will be set in
USBDevIntSt.
Reserved, user software should not write ones to reserved
bits. The value read from a reserved bit is not defined.
Description
Read mode control. Enables reading data from the OUT
endpoint buffer for the endpoint specified in the
LOG_ENDPOINT field using the USBRxData register.
This bit is cleared by hardware when the last word of
the current packet is read from USBRxData.
Read mode is disabled.
Read mode is enabled.
Write mode control. Enables writing data to the IN
endpoint buffer for the endpoint specified in the
LOG_ENDPOINT field using the USBTxData register.
This bit is cleared by hardware when the number of
bytes in USBTxLen have been sent.
Write mode is disabled.
Write mode is enabled.
reserved bits. The value read from a reserved bit is not
defined.
Logical Endpoint number.
Reserved, user software should not write ones to
Chapter 13: LPC24XX USB device controller
UM10237
© NXP B.V. 2009. All rights reserved.
for more
352 of 792
Reset
value
0x000
NA
0x0
Reset
value
0
0
NA